bs英國標準】bs en 617547 fibre optic interconnecting devices and passive components — fibre

《bs英國標準】bs en 617547 fibre optic interconnecting devices and passive components — fibre》由會員分享，可在線閱讀，更多相關《bs英國標準】bs en 617547 fibre optic interconnecting devices and passive components — fibre（31頁珍藏版）》請?jiān)谘b配圖網上搜索。

1、BRITISH STANDARD BS EN 61754-7:2008 Fibre optic interconnecting devices and passive components — Fibre optic connector interfaces — Part 7: Type MPO connector family ICS 33.180.20

2、 BS EN 61754-7:2008 National foreword This British Standard is the UK implementation of EN 61754-7:2008. It is identical to IEC 61754-7:2008. It supersedes BS EN 61754-7:2005 which is withdrawn. The UK participation in its prepa

3、ration was entrusted by Technical Committee GEL/86, Fibre optics, to Subcommittee GEL/86/2, Fibre optic interconnecting devices and passive components. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to inc

4、lude all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was publi

5、shed under the authority Strategy Committee on 31 October 2008 ? BSI 2008 ISBN 978 0 580 57566 2 Amendments/corrigenda issued since publication Date Comments EUROPEAN STANDARD EN 61754-7 NORME EUROPéENNE EUROP?ISCHE NORM June 2008 ICS 33.180.20 Supersedes EN 617

6、54-7:2005 English version Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 7: Type MPO connector family (IEC 61754-7:2008) Dispositifs d'interconnexion et composants passifs à fibres optiques - Interfaces de connecteurs pour

7、fibres optiques - Partie 7: Famille de connecteurs de type MPO (CEI 61754-7:2008) Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 7: Steckverbinderfamilie der Bauart MPO (IEC 61754-7:2008) This European Sta

8、ndard was approved by CENELEC on 2008-04-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

9、 concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CE

10、NELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hun

11、gary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation E

12、lectrotechnique Europ?isches Komitee für Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels ? 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 61754-7:2008 E Foreword The te

13、xt of document 86B/2581/CDV, future edition 3 of IEC 61754-7, prepared by SC 86B, Fibre optic interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 61754-7 on 2008-04-01. This European Standard

14、 supersedes EN 61754-7:2005. Specific technical changes involve the addition of an aligned key adaptor interface definition to address all existing MPO applications The following dates were fixed: – latest date by which the EN has to be implemented at national level by publication of an i

15、dentical national standard or by endorsement (dop) 2009-01-01 – latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-04-01 The International Electrotechnical Commission (IEC) and CENELEC draw attention to the fact that it is claimed that com

16、pliance with this document may involve the use of a patent concerning MPO connectors. The IEC and CENELEC take no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under r

17、easonable and non- discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holder of this patent right is registered with the IEC. Information may be obtained from: Intellectual Property Department, Nippon Telegraph and Telephone Corporatio

18、n, 20-2 Nishi-shinjuku 3-Chome Shinjukuku, Tokyo 163-14, Japan. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights other than those identified above. IEC and CENELEC shall not be held responsible for identifying any or all such pa

19、tent rights. Endorsement notice The text of the International Standard IEC 61754-7:2008 was approved by CENELEC as a European Standard without any modification. CONTENTS 1 Scope ...................................................................................................

20、............................ 4 2 Description ....................................................................................................................... 4 3 Interfaces ......................................................................................................................

21、...4 Figure 1 – MPO connector configurations ................................................................................5 Figure 2 – MPO female plug connector angled interface .......................................................... 6 Figure 3 – Optical datum target location diagrams .

22、.................................................................. 8 Figure 4 – Gauge pin............................................................................................................. 10 Figure 5 – Gauge for plug.......................................................................

23、............................... 11 Figure 6 – MPO male plug connector angled interface ........................................................... 12 Figure 7 – MPO adaptor interface .......................................................................................... 14 Figure 8 – MPO femal

24、e plug connector flat interface .............................................................. 16 Figure 9 – MPO male plug connector flat interface ................................................................. 18 Figure 10 – MPO backplane housing interface .....................................

25、................................. 20 Figure 11 – MPO printed board housing interface .................................................................. 23 Figure 12 – MPO aligned key adaptor interface...................................................................... 26 Table 1 – Dimensi

26、ons of the MPO female plug connector angled interface ............................... 7 Table 2 – Dimensions of the gauge pin .................................................................................. 10 Table 3 – Dimensions of the gauge for plug ...........................................

27、................................ 11 Table 4 – Dimensions of the MPO male plug connector angled interface ................................ 13 Table 5 – Dimensions of the MPO adaptor interface .............................................................. 15 Table 6 – Dimensions of the MPO female p

28、lug connector flat interface .................................. 17 Table 7 – Dimensions of the MPO male plug connector flat interface ..................................... 19 Table 8 – Dimensions of the MPO backplane housing ............................................................ 22 Table 9

29、– Grade .................................................................................................................... 23 Table 10 – Dimensions of the MPO printed board housing interface ....................................... 25 Table 11 – Dimensions of the MPO aligned key adaptor interface

30、 .......................................... 27 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS – FIBRE OPTIC CONNECTOR INTERFACES – Part 7: Type MPO connector family 1 Scope This part of IEC 61754 defines the standard interface dimensions for type MP

31、O family of connectors. 2 Description The parent connector for type MPO connector family is a multiway plug connector charac- terized by a rectangular ferrule normally 6,4 mm × 2,5 mm which utilizes two pins of 0,7 mm diameter as its alignment. It is applicable to a joint of multi

32、ple fibres up to 12 fibres by arraying them between two pin-positioning holes in the ferrule. Furthermore, it is capable of joining up to 24 fibres by arraying them with a two layer arrangement. The connector includes a push-pull coupling mechanism and a ferrule spring loaded in the direct

33、ion of the optical axis. The connector has a single male key which may be used to orient and limit the relative position between the connector and the component to which it is mated. Connector interfaces are configured using a female plug without pins, a male plug with pins fixed and an ad

34、aptor as shown in Figure 1. The female plug is intermateable with the male plug. Moreover, connector interfaces between the female plug and the male plug are configured by applying a backplane housing and a printed board housing instead of the adaptor. 3 Interfaces This standard contain

35、s the following standard interfaces: Interface 7-1: MPO female plug connector angled interface – Push/pull consisting of: Interface 7-1-1 for 2 to 12 fibres Interface 7-1-2 for 16 to 24 fibres Interface 7-2: MPO male plug connector angled interface – Push/pull consisting of: Interface 7-2-1 for

36、 2 to 12 fibres Interface 7-2-2 for 16 to 24 fibres Interface 7-3: MPO adaptor interface – Push/pull Interface 7-4: MPO female plug connector flat interface – Push/pull consisting of: Interface 7-4-1 for 2 to 12 fibres Interface 7-4-2 for 16 to 24 fibres Interface 7-5: MPO male plug connector f

37、lat interface – Push/pull consisting of: Interface 7-5-1 for 2 to 12 fibres Interface 7-5-2 for 16 to 24 fibres Interface 7-6: MPO backplane housing interface – Self-retaining Interface 7-7: MPO printed board housing interface – Self-retaining Interface 7-8: MPO adaptor interface – Push/pu

38、ll, aligned key configuration The following standards are intermateable: Female plugs 7-1-1 Adaptors/housings 7-3 Male plugs 7-2-1 7-1-2 7-3 7-2-2 7-4-1 7-3 and 7-8 7-5-1 7-4-2 7-3 and 7-8 7-5-2 7-1-1 7-6 and 7-7 7-2-1 7-1-2 7-6 and 7-7 7-2-2 7-4-1 7-6 and 7-7 7-5-

39、1 7-4-2 7-6 and 7-7 7-5-2 NOTE Connector interfaces among 2 to 12 fibres will intermate and will correctly align the lower defined numbers of optical datum targets. Also connector interfaces among 16 to 24 fibres will intermate and will correctly align the lower defined numbers of optic

40、al datum targets. Female plug Adaptor Male plug Backplane housing Printed board housing IEC 1065/2000 Figure 1 – MPO connector configurations Z R Q P K I O ?A C D ?E ?F ?G ?H

41、S J N AC AB Y L AA Coupling sleeve M  T U X Pin-holes  See Figure 3 ? AD IEC 395/08 Figure 2 – MPO female plug connector angled interface Table 1 – Dimensions of the MPO female plug connector angled inter

42、face Reference Dimensions Notes Minimum Maximum A C D E F G H I J K L M N O P Q R S T U AA AB AC AD 0,699 mm 4,597 mm 6,3 mm 8,34 mm 9,49 mm 10,85 mm 12,19 mm 8,8 mm 7,9 mm 1,4 mm 0,2 mm 2,4 mm 2,8 mm 4,89 mm 5,59 mm 5,7 mm – 2,9 mm

43、 – 2,4 mm 42° – – 7,5° 0,701 mm 4,603 mm 6,5 mm 8,54 mm 9,59 mm 11,05 mm 12,59 mm 9,2 mm 8,1 mm – 0,8 mm 2,6 mm 3,0 mm 4,99 mm 5,69 mm – 7,7 mm 3,1 mm 0,8 mm 2,5 mm 45° 45° 45° 8,5° 1 2 3

44、 4 and 5 NOTE 1 Each pin-hole must accept a gauge pin as shown in Figure 4 to a depth of 5,5 mm with a maximum force of 1,7 N. In addition, two pin-holes of a plug must accept a gauge as shown in Figure 5 to a depth of 5,5 mm with a maximum force of 3,4 N. NOTE 2 Dimension C is defined

45、 as the distance between two pin-hole centres. NOTE 3 Dimension I is given for a fibre endface centre of a plug end when not mated. It is noticed that a ferrule is movable by a certain axial compression force, and therefore dimension I is variable. Ferrule compression force must be 7,8 N to 11,

46、8 N when a position of the fibre endface from the datum Z is in the range of 8,2 mm to 8,4 mm. NOTE 4 Coupling sleeve must be movable by a certain axial compression force. Dimension L is given for a coupling sleeve end when not mated. Coupling sleeve compression force must be 2,

47、9 N to 6,9 N when a position of the coupling sleeve endface from datum Z is in the range of 0 mm to 0,1 mm to the right or to the left of datum Z. NOTE 5 An adaptor coupling part must be unlocked by a left-direction movement of a coupling sleeve, when it is separate from an adaptor. W hen

48、 the coupling sleeve is moved for unlocking, a position of the coupling sleeve endface must be larger than 2,0 mm in the left direction from the datum Z. 0,125 0,125 X 0,125 0,375 0,375 X 0,125 0,125 0,375 0,625 0,875 0,375 0,625 0,875 Y Y Y

49、 X 0,125 0,125 Two fibres Four fibres Eight fibres 0,125 0,375 0,625 0,375 0,625 0,875 1,125 0,875 1,125 0,125 0,125 0,375 0,625 0,875 1,125 1,375 0,375 0,625 0,875 1,125 1,375 Y Y X

50、 Ten fibres  Twelve fibres  IEC 1594/04 X Figure 3 – Optical datum target location diagrams (1 of 2) 0,250 0,250 0,125 0,125 X 0,250 0,250 0,375 0,625 0,875 0,375 0,625 0,875 0,125 0,125 0,375 0,625 0,875 1,125 0,375 0,625

51、 0,875 1,125 Y Y X Sixteen fibres 0,125 0,125 0,250 0,250  Twenty fibres 0,375 0,625 0,875 1,125 1,375 0,375 0,625 0,875 1,125 1,375 Y X Twenty four fibres IEC 1595/04

52、 NOTE The optical datum target location diagram is shown in the figure. Here, datum X is defined as the line passing through two pin-hole centres, and datum Y is defined as the line perpendicular to datum X and passing through the midpoint of two pin-hole centres. Figure 3

53、(2 of 2) ?BA ?A BB BC B 0,0005 IEC 1596/04 Figure 4 – Gauge pin Table 2 – Dimensions of the gauge pin Reference Dimensions mm Notes Minimum Maximum A B BA BB BC 0,698 5 10,8 0,2 0,2 6,0 0,699 0 11,2 0

54、,4 0,5 – 1 2 NOTE 1 Surface roughness Rz = 0,1 μm for the length of dimension BC. NOTE 2 Typical dimensions. ?0,001 W ?BA ?A D C W BB U BC 0,000 5 IEC 396/08 Figure 5 – Gauge for plug Table 3 – Dimensions of

55、 the gauge for plug Reference Dimensions mm Notes Minimum Maximum A C D U BA BB BC 0,698 5 4,599 5 6,3 2,4 0,2 0,2 6,0 0,699 0 4,600 5 6,5 2,5 0,4 0,5 6,5 For two pins, 1 2 2 NOTE 1 Surface roughness Rz = 0,1 μm. NOTE 2 Typical

56、 dimensions. Z ?0,002 W K I J AC ?A C D ?E ?F ?G ?H AB  R Q P S Guide-pin O N Y L AA Coupling sleeve M W Guide-pin  See Figure 3 ?BA U BB T AD CA X IEC 397/08 Figure 6 – MPO male plug co

57、nnector angled interface Table 4 – Dimensions of the MPO male plug connector angled interface Reference Dimensions Notes Minimum Maximum A C D E F G H I J K L M N O P Q R S T U AA AB AC AD BA BB CA 0,697 mm 4,597 mm 6,3 mm 8,34 mm 9,49 mm 10,85 mm 12,19 mm 8,8 mm 7,9 mm

58、 1,4 mm 0,2 mm 2,4 mm 2,8 mm 4,89 mm 5,59 mm 5,7 mm – 2,9 mm – 2,4 mm 42o – – 7,5o 0,2 mm 0,2 mm 1,6 mm 0,699 mm 4,603 mm 6,5 mm 8,54 mm 9,59 mm 11,05 mm 12,59 mm 9,2 mm 8,1 mm – 0,8 mm 2,6 mm 3,0 mm 4,99 mm 5,69 mm – 7,7 mm 3,1 mm 0,8 mm 2,5 mm 45o 45o 45o

59、8,5o 0,4 mm 0,5 mm 3,3 mm 1 2 3 4 and 5 6 NOTE 1 Each guide pin must be retained with a minimum force of 19,6 N. Surface roughness Rz must be below 0,5 μm. NOTE 2 Dimension C is defined as the distance between two guide-pin centr

60、es. NOTE 3 Dimension I is given for a fibre endface centre of a plug end when not mated. It is noticed that a ferrule is movable by a certain axial compression force, and therefore the dimension I is variable. Ferrule compression force must be 7,8 N to 11,8 N when a position of the fi

61、bre endface from the datum Z is in the range of 8,2 mm to 8,4 mm. NOTE 4 Coupling sleeve must be movable by a certain axial compression force. Dimension L is given for a coupling sleeve end when not mated. Coupling sleeve compression force must be 2,9 N to 6,9 N when a position of the couplin

62、g sleeve endface from datum Z is in the range of 0 mm to 0,1 mm to the right or to the left of datum Z. NOTE 5 An adaptor coupling part must be unlocked by a left-direction movement of a coupling sleeve, when it is separate from an adaptor. W hen the coupling sleeve is moved for unlocking, a

63、 position of the coupling sleeve endface must be larger than 2,0 mm in the left direction from the datum Z. NOTE 6 The top shape of guide-pin may be a round shape that is symmetrical about the guide-pin axis with a minimum radius of 0,15 mm. R P O X N Z I S ?H ?W V A

64、AB ?F ?E B B K V AA A Keyways opposed  L M Section A-A Section B-B  IEC 398/08 Figure 7 – MPO adaptor interface Table 5 – Dimensions of the MPO adaptor interface Reference Dimensions mm

65、 Notes Minimum Maximum E F H I K L M N O P R S V W X AA AB 8,54 mm 9,6 mm 12,6 mm 8,2 mm – 0 1,6 mm 2,4 mm 5,0 mm 5,7 mm 7,8 mm 3,4 mm 0,95 mm 11,8 mm 3,4 mm 45° 45° 8,74 mm 9,7 mm – 8,4 mm 1,39 mm 0,1 mm 2,0 mm 2,6 mm 5,1 mm 5,9 mm – 3,6 mm 1,15 mm 12,2 mm

66、– 48° 50° 1 NOTE 1 Dimension L is the distance from datum Z to a latch-ledge end. The latch-ledge end may be located to the right or to the left of datum Z. R Z Q X P K I O J N AC ?A C D ?E ?F ?G ?H S AB Y AA L Coupling sleeve M  U Pin-holes  See Figure 3 IEC 399/08 Figure 8 – MPO female plug connector flat interface Table 6 – Dimensions of t