《bs英國標準】bs en 13101 steps for underground man entry chambersrequirements, marking, testing and evaluation of conformity》由會員分享，可在線閱讀，更多相關《bs英國標準】bs en 13101 steps for underground man entry chambersrequirements, marking, testing and evaluation of conformity（41頁珍藏版）》請在裝配圖網(wǎng)上搜索。
1、Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
BRITISH STANDARD BS EN
13101:2002
Steps for underground man entry chambers — Requirements, marking, testing and evaluation of conformity
The European Stand
2、ard EN 13101:2002 has the status of a
British Standard
ICS 97.145
BS EN 13101:2002
National foreword
This British Standard is the official English language version of EN 13101:2002.
3、EN 13101 is a candidate “harmonized” European Standard and fully takes into account the requirements of the European Commission mandate M118 “Waste water engineering products”, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date of applicabil
4、ity of
EN 13101 as a harmonized European Standard, i.e. the date after which this standard may be used for CE marking purposes, is subject to an announcement in the Official
Journal of the European Communities.
The Commission in consultation with Member States have agreed a transition period for
5、the co-existence of harmonized European Standards and their corresponding national standard(s). It is intended that this period will comprise a period, usually nine months, after the date of availability of the European Standard, during which any required changes to national regulations are to be ma
6、de, followed by a further period, usually of 12 months, for the implementation of CE marking. At the end of this co- existence period, the national standard(s) will be withdrawn.
EN 13101 is the subject of transitional arrangements agreed under the Commission mandate. In the UK, the correspondin
7、g national standards are:
— BS 1247-1:1990, Specification for galvanized ferrous or stainless steel manhole steps.
— BS 1247-2:1990, Specification for plastics encapsulated manhole steps.
— BS 1247-3:1991, Specification for aluminium manhole steps.
and based on this transition period of twenty-o
8、ne months, BS 1247-1:1990, BS 1247-2:1990 and BS 1247-3:1991 would be withdrawn in June 2004.
NOTE This date is approximate. Users of this standard should contact BSI Customer Services for confirmation of withdrawal.
The UK participation in its preparation was entrusted to Technical Committee
9、B/505, Wastewater engineering, which has the responsibility to:
— aid enquirers to understand the text;
— present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;
— monitor related international
10、 and European developments and promulgate them in the UK.
A list of organizations represented on this committee can be obtained on request to its secretary.
This British Standard, having been prepared under the direction of the Building and Civil Engineering Sector Policy and Strategy
11、Committee, was published under the authority of the Standards Policy and Strategy Committee on
14 November 2000
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
Amd. No.
Date
Comments
? BSI 14 November 2002
ISBN 0 5
12、80 40726 8
Amendments issued since publication
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
BS EN 13101:2002
Cross-references
The British Standards which implement international or European publications referred to in this document may be found in the BS
13、I Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.
This publication does not purport to include all the necessary provisions of a contract. Users are responsible
14、for its correct application.
Compliance with a British Standard does not of itself confer immunity from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, page i, a blank page, the EN
title page, pages 2 to 35 and a back cover.
15、The BSI copyright date displayed in this document indicates when the document was last issued.
? BSI 14 November 2002 i
blank
ii
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BS
16、I
EUROPEAN STANDARD NORME EUROPéENNE
EUROP?ISCHE NORM
EN 13101
October 2002
ICS
English version
Steps for underground man entry chambers - Requirements, marking, testing and evaluation of conformity
Echelons de trou d'homme - Prescriptions, marquage, essai,
17、et évaluation de la conformité
Steigeisen für Steigeiseng?nge in Sch?chten - Anforderungen, Kennzeichnung, Prüfung und Beurteilung der Konformit?t
This European Standard was approved by CEN on 1 August 2002.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
18、stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Management Centre or to any CEN member.
This European Stand
19、ard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official versions.
CEN members are the national stan
20、dards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDI
21、ZATION C O M I Té EUR O P éEN DE NOR M A L I S A TI ON EUR O P ? I S C H ES KOM I TEE F ü R NOR M UNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
? 2002 CEN All rights of exploitation i
22、n any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN 13101:2002 E
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
Contents
Foreword ......................................................................................
23、................................................................................4
1 Scope ..............................................................................................................................................................5
2 Normative references .....................
24、...............................................................................................................5
3 Terms and definitions....................................................................................................................................6
4 Requirements .........
25、........................................................................................................................................6
4.1 General .....................................................................................................................................................
26、.......6
4.2 Materials..........................................................................................................................................................6
4.2.1 Metals ...........................................................................................................
27、...................................................6
4.2.2 Plastics encapsulation ..................................................................................................................................7
4.3 Design requirements ............................................................
28、.........................................................................7
4.3.1 Types ...............................................................................................................................................................7
4.3.2 Dimensions .................................
29、....................................................................................................................7
4.3.3 Limit of insertion of step .............................................................................................................................10
4.3.4 Surface condi
30、tion.........................................................................................................................................10
4.3.5 Corrosion resistance ................................................................................................................................
31、...10
4.3.6 Twist ..............................................................................................................................................................11
4.3.7 Vertical loading ................................................................................................
32、............................................11
4.3.8 Proof load — Non-ductile materials (Grey cast iron) ...............................................................................11
4.3.9 Resistance to pull-out ..................................................................................
33、...............................................11
4.3.10 Resistance to impact ...................................................................................................................................11
4.3.11 Integrity of plastics encapsulation..........................................
34、...................................................................11
4.3.12 Thickness of plastics encapsulation .........................................................................................................12
4.3.13 Integrity of galvanizing ...........................................
35、.....................................................................................12
5 Testing ..........................................................................................................................................................12
6 Marking and designation..............
36、...............................................................................................................12
6.1 Marking .........................................................................................................................................................12
6.2 Designation.
37、..................................................................................................................................................13
7 Evaluation of conformity .........................................................................................................................
38、....13
7.1 General ..........................................................................................................................................................13
7.2 Type testing (initial testing of the product) ........................................................................
39、.......................13
7.3 Factory production control (FPC) ..............................................................................................................14
7.3.1 General ............................................................................................................
40、..............................................14
7.3.2 Equipment.....................................................................................................................................................14
7.3.3 Raw materials and components ...............................................
41、..................................................................14
7.3.4 Product testing and evaluation ..................................................................................................................14
7.3.5 Non conforming products .............................................
42、..............................................................................15
Annex A (normative) Twist test................................................................................................................................16
A.1 Apparatus ........................................
43、.............................................................................................................16
A.2 Procedure .....................................................................................................................................................16
A.3 Test report ....
44、................................................................................................................................................16
Annex B (normative) Vertical loading test ...........................................................................................................
45、...17
B.1 Apparatus .....................................................................................................................................................17
B.2 Procedure ................................................................................................................
46、.....................................17
B.3 Test report ....................................................................................................................................................17
Annex C (normative) Proof load test for grey cast iron steps ...........................
47、...................................................18
C.1 Apparatus .....................................................................................................................................................18
C.2 Procedure ................................................................
48、.....................................................................................18
C.3 Test report ....................................................................................................................................................18
Annex D (normative) Pull out/anchorage t
49、est ........................................................................................................19
D.1 Apparatus .....................................................................................................................................................19
Licensed copy:PONTY
50、PRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
D.2 Preparation ................................................................................................................................................... 19
D.2.1 Method 1 - For steps designed to be factory fixed into pre-cast c
51、oncrete............................................ 19
D.2.2 Method 2 - For steps designed to be fixed into masonry or concrete during construction ................ 19
D.2.3 Method 3 - For steps designed to be fixed after construction ...............................................................
52、. 19
D.2.4 Method 4 - For steps designed to be replaced ......................................................................................... 19
D.3 Procedure .......................................................................................................................................
53、.............. 19
D.4 Test report .................................................................................................................................................... 19
Annex E (normative) Impact test ..............................................................................
54、............................................... 21
E.1 Apparatus ..................................................................................................................................................... 21
E.2 Procedure ..................................................................
55、................................................................................... 21
E.3 Test report .................................................................................................................................................... 21
Annex F (normative) Method of test for in
56、tegrity of plastics encapsulation ...................................................... 23
F.1 Apparatus ..................................................................................................................................................... 23
F.2 Procedure .........................
57、............................................................................................................................ 23
F.3 Test report .................................................................................................................................................... 23
58、Annex G (Normative) Method of test for integrity of plastics encapsulation (dry conditions) ......................... 25
G.1 Apparatus ..................................................................................................................................................... 25
G.1.1 Pore
59、 detector ................................................................................................................................................ 25
G.2 Procedure ...............................................................................................................................
60、...................... 25
G.3 Test report .................................................................................................................................................... 25
Annex H (normative) Method of test for thickness of plastics encapsulation............................
61、........................ 26
H.1 Apparatus ..................................................................................................................................................... 26
H.2 Procedure .........................................................................................
62、............................................................ 26
H.3 Test report .................................................................................................................................................... 26
Annex I (informative) Evaluation of conformity by third party .
63、............................................................................ 27
I.1 General.......................................................................................................................................................... 27
I.2 Procedure of the third party control ........
64、.................................................................................................. 27
I.3 Report by the third party ............................................................................................................................. 28
Annex ZA (informative) Clauses of
65、this European Standard addressing essential requirements or other provisions of EU Directives ........................................................................................................................ 29
Bibliography ..................................................................
66、............................................................................................ 35
Licensed copy:PONTYPRIDD COLLEGE, 15/12/2006, Uncontrolled Copy, ? BSI
Foreword
This document (EN 13101:2002) has been prepared by Technical Committee CEN /TC 165, "Waste water engineering" the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement
bs英國標準】bs en 13101 steps for underground man entry chambersrequirements, marking, testing and evaluation of conformity
