《【BS英國標準】BS EN 137442004 Surfaces for sports areas. Procedure for accelerated ageingimmer》由會員分享，可在線閱讀，更多相關《【BS英國標準】BS EN 137442004 Surfaces for sports areas. Procedure for accelerated ageingimmer（9頁珍藏版）》請?jiān)谘b配圖網上搜索。
1、BRITISH STANDARD BS EN
13744:2004
Surfaces for sports areas — Procedure for accelerated ageing by immersion in hot water
The European Standard EN 13744:2004 has the status of a
British Standard
I
2、CS 97.150; 97.220.10
BS EN 13744:2004
National foreword
This British Standard is the official English language version of
EN 13744:2004.
The UK participation in its preparation was entrusted to Tec
3、hnical Committee
PRI/57, Surfaces for sports areas, which has the responsibility to:
— aid enquirers to understand the text;
— present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed;
— mon
4、itor related international and European developments and promulgate them in the UK.
A list of organizations represented on this committee can be obtained on request to its secretary.
Cross-references
The British Standards which implement international or European publications referred to in thi
5、s document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online.
This publication does not purport to include all the necessary provisions of a
6、contract. Users are responsible for its correct application.
Compliance with a British Standard does not of itself confer immunity from legal obligations.
This British Standard was published under the authority of the Standards Policy and Strategy Committee on
13
7、 October 2004
? BSI 13 October 2004
ISBN 0 580 44597 6
Summary of pages
This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover.
The BSI copyright notice displayed in this document indicates when the documen
8、t was last issued.
Amd. No.
Date
Comments
Amendments issued since publication
EUROPEAN STANDARD NORME EUROPéENNE
EUROP?ISCHE NORM
EN 13744
October 2004
ICS 97.150; 97.220.10
English version
Surfaces for sports areas - Procedure fo
9、r accelerated ageing by immersion in hot water
Sols sportifs - Méthode de vieillissement accéléré par immersion dans l'eau chaude
Sportb?den - Verfahren der beschleunigten Alterung durch
Eintauchen in hei?es Wasser
This European Standard was approved by CEN on 29 July 2004.
CEN m
10、embers are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applic
11、ation to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has
12、 the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
13、Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I Té EUR O P éEN DE NOR M A L I S A TI ON EUR O P ? I S C H ES KOM I TEE F ü R NOR M UNG
Management Centre: rue de
14、Stassart, 36 B-1050 Brussels
? 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN 13744:2004: E
EN 13744:2004 (E)
Contents
Page
Foreword.................................................
15、.............................................................................................................3
1 Scope ......................................................................................................................................................4
2 Principle ...........
16、.......................................................................................................................................4
3 Apparatus ...............................................................................................................................................4
17、4 Test pieces .............................................................................................................................................4
5 Procedure ................................................................................................................................
18、...............4
6 Comparison tests...................................................................................................................................5
7 Calculation and expression of results.......................................................................................
19、..........5
8 Test report ..............................................................................................................................................5
5
Foreword
This document (EN 13744:2004) has been prepared by Technical Committee CEN/TC 217 “Surfac
20、es for sports areas”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by
21、 April 2005.
It is one of two standards for procedures for ageing surfaces for sports areas. The other standard in this series has the following title:
EN 13817, Surfaces for sports areas — Procedures for accelerated ageing by exposure to hot air
According to the CEN/CENELEC Internal Regula
22、tions, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Nor
23、way, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
1 Scope
This document describes a procedure for subjecting test pieces taken from surfaces for sports areas to accelerated ageing by immersion in hot water. Test pieces are aged to permit a comp
24、arison of their physical characteristics before and after ageing in accordance with European Standard test methods for surfaces for sports areas.
This method is suitable for ageing all types of sports surfaces, except for wooden surfaces, using test pieces in the laboratory, but is primarily inte
25、nded for ageing polymeric surfaces. The procedure allows a measure of the effect on the physical characteristics of the sports surface due to exposure to water at elevated temperatures to be made.
NOTE Results from tests on materials which exhibit temporary changes in properties due to moisture
26、should be interpreted with caution.
2 Principle
Test pieces are exposed to water at an elevated temperature to permit selected physical characteristics of the surface to be assessed before and after test.
3 Apparatus
3.1 Water bath, capable of being maintained at (70 ± 2) °C.
27、3.2 Small weights, to assist with immersion if necessary.
4 Test pieces
Select, prepare and condition the test piece(s) in accordance with the appropriate method of test.
Test pieces shall be such that no mechanical, chemical or heat treatment will be required after their removal from t
28、he water bath.
Any material used for marking test pieces shall not be applied in any critical area of the test piece and shall not damage the surface or be destroyed during ageing.
NOTE Wherever possible, marking should be carried out after ageing of the test piece.
5 Procedure
Immer
29、se test pieces in the water bath (3.1) maintained at a temperature of (70 ± 2) °C, the test pieces being freely exposed to the ageing environment on all sides. If necessary, use the small weights (3.2) to submerge the test pieces in the water bath.
Leave the test pieces in the water bath for (336
30、 ± 2) h.
Remove the test pieces from the water bath and condition them together with an un-aged sample for not less than 16 h and for no more than 6 d in a relaxed condition in accordance with the test method for the particular characteristic being assessed.
NOTE Simultaneous ageing of differe
31、nt test pieces in the same water bath should be avoided, to prevent migration of anti-degradants or plasticizers, etc.
6 Comparison tests
To compare properties before and after accelerated ageing, carry out tests on un-aged test pieces at the same time and under the same conditions as th
32、ose on test pieces having been subjected to accelerated ageing. Only compare test pieces of similar dimensions and having approximately the same exposed areas.
7 Calculation and expression of results
Calculate the results as specified by the appropriate method of test. If required, calcula
33、te the percentage change in the property using the following expression:
C = A ? O ×100
O
where
C is the percentage change in the property;
A is the aged value of the property, e.g. % impact absorption;
O is the un-aged value of the property.
8 Test report
The test report s
34、hall include the following:
a) reference to this document, i.e. EN 13744:2004;
b) reference to the procedure used to select the test pieces and determine their characteristics, e.g. a
European Standard test method;
c) complete identification of the surface tested including man
35、ufacturer’s reference, type and depth of supporting layers, and method of attachment and previous history;
d) physical characteristics determined, with their values before and after ageing, and, if required, their percentage change, calculated in accordance with Clause 7;
e) individual
36、test results, if required.
BS EN
13744:2004
BSI
389 Chiswick High Road
London
W4 4AL
BSI — British Standards Institution
BSI is the independent nat
37、ional body responsible for preparing
British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.
Revisions
British Standards are updated by amendment or revision. Users of
British Standards should make sure that they
38、possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the
39、identity of which can be found on the inside front cover.
Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.
BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.
Buying standards
Orders for all
40、 BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001.
Fax: +44 (0)20 8996 7001. Email: orders@bsi-. Standards are also
available from the BSI website at http://www.bsi-.
In response to orders for international standards, it is
41、 BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.
Information on standards
BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exp
42、orters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre.
Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: info@bsi-.
Subscribing members of BSI are kept up to date with standards
43、developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001.
Email: membership@bsi-.
Information regarding online access to British Standards via
44、British Standards
Online can be found at http://www.bsi-
Further information about BSI is available on the BSI website at http://www.bsi-.
Copyright
Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardizatio
45、n bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means – electronic, photocopying, recording or otherwise – without prior written permission from BSI.
This does not precl
46、ude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.
Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553.
Email: copyright@bsi-.
國內外標準大全
豆丁網國內外標準下載地址
【BS英國標準】BS EN 137442004 Surfaces for sports areas. Procedure for accelerated ageingimmer
