喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有,,請放心下載，原稿可自行編輯修改【QQ：1304139763 可咨詢交流】=====================
喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有,,請放心下載，原稿可自行編輯修改【QQ：414951605 可咨詢交流】=====================
I 4座微型客貨兩用車設計（離合器及操縱機構設計） 摘 要 離合器是直接連接發動機和傳動系統中的總成之一.他主要包含主動部分,從 動部分,壓緊機構和操縱機構等四部分. 主動部分,從動部分和壓緊機構是保證離合器處于接合狀態并能傳遞動力的 基本結構.操作機構是使離合器分離的機構.正是這四部分機構之間相互協調配合,已 達到汽車起步時將發動機與傳動系平順地接合,換檔式將發動機與傳動系分離,減 少變速箱內齒輪的沖擊. 本次設計主要對4微型座客貨兩用車的離合器進行設計。首先對離合器進行 了結構上的設計，此離合器選用的是膜片彈簧推式離合器。結構和方式選定后對 此方案進行了計算，主要計算內容如下： 摩擦片主要參數的選擇 膜片彈簧主要參數的選擇 摩擦片基本參數的優化 扭轉減振器設計 離合器踏板行程及踏板力的計算 從動盤總成的設計計算與參數選擇 關鍵詞：離合器，摩擦片，膜片彈簧，操縱機構 車輛與動力工程學院畢業說明書 II 4 MICRO- DUAL-USE CAR DESIGN (CLUTCH AND THE MANIPULATION OF BODY DESIGN) ABSTRACT Clutch is directly connected to the engine and transmission system in one of the assembly. He mainly includes part of the initiative, part of the driven, pinched agencies and institutions, such as manipulation of four parts. Part of the initiative, pinched and driven some institutions in the clutch engagement is to ensure that state power and to convey the basic structure. Clutch operation is to separate bodies of the institutions. It is precisely this four-part mutual coordination and cooperation between agencies, have reached the car at the start Engine and transmission system will smooth the joint, transmission and engine-transmission system will be separated to reduce the impact of gear in the gearbox. The design of the four major micro-Block dual-use car the clutch design. First a clutch of structural design, this is the choice of clutch diaphragm spring push-type clutch. Structure and approach selected this option were calculated mainly calculated as follows: Friction main parameters of the choice of films Diaphragm spring main parameters of choice The basic parameters of friction-optimized Reversing the shock absorber design Clutch pedal and the itinerary of the calculation Assembly-driven computing and the design parameters KEY WORD: clutch, friction films, silent spring, the manipulation of body 車輛與動力工程學院畢業說明書 III 目 錄 第一章 緒 論...........................................1 1.1 選題的目的. ....................................1 1.2 離合器發展歷史.................................1 1.3 離合器概述......................................2 1.3.1 離合器的功用................................3 1.3.2 現代汽車離合器應滿足的要求.................. 3 1.3.3 離合器工作原理............................4 1.3.4 推式膜片彈簧離合器的優點...................5 1.4 設計的預期成果.................................5 第二章 離合器的結構設計................................7 2.1 離合器結構選擇與論證............................7 2.1.1 摩擦片的選擇..............................7 2.1.2 壓緊彈簧布置形式的選擇....................7 2.1.3 壓盤的驅動方式.............................8 2.1.4 分離杠桿、分離軸承..........................8 2.1.5 離合器的散熱通風..........................9 2.1.6 從動盤總成................................9 2.2 離合器結構設計的要點..........................10 2.3 離合器主要零件的設計.........................11 2.3.1 從動盤.....................................11 2.3.2 摩擦片.....................................11 2.3.3 膜片彈簧...... ..........................12 2.3.4 壓盤....................................12 2.3.5 離合器蓋...............................12 2.4 本章小結...................................13 第三章 離合器的設計計算及說明........................14 3.1 離合器設計所需數據...........................14 3.2 摩擦片主要參數的選擇...........................14 車輛與動力工程學院畢業說明書 IV 3.2.1 后備系數 .................................14 3.2.2 摩擦片的外徑...........................15 3.2.3 摩擦片的摩擦因數...........................16 3.2.4 單位壓力 ...............................160P 3.3 摩擦片基本參數的優化............................17 3.4 膜片彈簧主要參數的選擇........................19 3.4.1 比較 H/h 的選擇.............................19 3.4.2 R/r 選擇..................................20 3.4.3 圓錐底角..................................20 3.4.4 切槽寬度...................................20 3.4.5 壓盤加載點半徑和支承環加載點半徑的確定. ...20 3.4.6 公差與精度...............................20 3.5 扭轉減振器設計.............................20 3.6 減震彈簧設計..................................21 3.7 操縱機構形式選擇...........................23 3.8 離合器踏板行程計算...........................24 3.9 踏板力的計算.................................25 3.10 從動盤總成............................26 3.10.1 從動盤的結構組成與選型........ .......26 3.10.2 從動盤總成設計............................26 3.11 本章小節.......................................33 第四章 結論..........................................34 參考文獻...............................................35 致謝..................................................36