濕式清掃車清掃機構的設計【卡車式】【含6張cad圖紙+文檔全套資料】

喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 密 級 分類號 編 號 成 績 本科生畢業設計 (論文) 外文翻譯 原 文 標 題 The construction and function of thenozzle nozzlennnozzle nozzle 譯 文 標 題 吸嘴的構造及功能 作者所在系別 機電工程學院 作者所在專業 車輛工程 作者所在班級 B13141 作 者 姓 名 趙利平 作 者 學 號 201322294 指導教師姓名 劉志強 指導教師職稱 講師 完 成 時 間 2017 年 3 月 北華航天工業學院教務處制 譯文標題 吸嘴的構造及功能 原文標題 The construction and function of the nozzle 作 者 Fritz Klocke,Christian Brecher 譯 名 弗里茨、克里斯蒂安 國 籍 德國 原文出處 ScienceDirect 吸嘴是掃路車的一個重要工作裝置，它是把前方掃刷掃進車輛中部的垃圾由地面輸送到垃圾箱體內的一種垃圾導向輸送裝置。吸嘴結構、性能的好壞直接影響到整車吸塵的效果。傳統吸嘴的結構已越來越不適應現在的道路條件，使用時間一長，就暴露出許多缺陷。為提高掃路車清掃能力，改進吸嘴結構已迫在眉睫。 首先，分析一下掃路車吸嘴的結構原理。它是由四面金屬板圍成，呈扁平狀，與地面圍成具有一定容積的腔體。頂部開口通過橡膠吸管與箱體相通，同箱體形成一個密閉倉體，前面為垃圾吸人口。整個吸嘴體由左右側及后部的橡膠滾輪支撐，調節滾輪機構使吸嘴底邊離地面間隙約為5—10mm。工作時，風機不斷的抽吸，使密閉箱體處于真空狀態，這樣吸嘴的周邊就形成一定的負壓。前方由掃刷攏于車輛中部的垃圾受到真空吸力的吸引，沿著箱體通道而被收集在箱體內。專用裝置停止工作時，吸嘴體通過提升機構收到一定的高度，保證車輛運輸行駛的安全性。因此針對吸嘴用途及使用環境，借鑒國內外先進掃路車吸嘴結構，對傳統型吸嘴。 1地面不平坦時，保證吸嘴接地間除均勻傳統吸嘴的提升機構采用平行四邊形機構。該機構通過銷軸一端與吸嘴支耳相連，另一端與車架相連，通過鋼絲繩收放使吸嘴升降。吸嘴體通過銷軸可繞該機構上下跳動，前后左右方向無法擺動。當遇到地面高低不平時(如圖3)，由于吸嘴無法擺動，隨著地面的升高，吸嘴體整體提升，而地勢低的一邊間隙就加大了，從而造成底部漏風，吸力下降，地面無法清掃干凈。新型吸嘴就能克服這種道路條件帶來的問題。吸嘴升降直接由油缸的伸縮來控制。油缸一端通過U形卸扣與吸嘴支耳相連，油缸為單作用缸，吸嘴放下時，活塞桿伸長，腔內無壓力，吸嘴隨路面高低而升降，油缸也會跟隨伸縮，使吸嘴不受約束。前方導向桿通過鉸接機構與吸嘴相連。鉸接機構由鉸接座和銷軸I、銷軸H組成。鉸接座的兩個銷孔成十字交叉布置，銷軸I連接導向桿和鉸接座，銷軸n連接鉸座和吸嘴體。吸嘴體可繞銷軸I前后擺動，繞銷軸n左右擺動。當路面高低不平時，吸嘴始終與地面保持平行，這樣離地間隙也均勻不變，風機吸力也不受影響，同時降低對地面撞擊的噪音，提高吸嘴的耐用性。 2提商對密度大、多而厘、有粘性的垃圾的吸力沙土型垃圾比較濕，壓實后對地面具有一定的附著力，傳統型吸嘴需靠提高風機轉速才能吸干凈。新型吸嘴尾部加裝臥式掃刷(如圖Zb)就能提高清掃效率。臥式掃刷裝在吸嘴后部，由5把圓形掃刷固定在心軸上，液壓馬達帶動心軸使掃刷高速旋轉。如果垃圾具有一定的粘性，真空吸力不足以克服垃圾對地面附著力，需通過掃刷的滾動，使垃圾揚起，真空吸力作用面積增大。根據壓強、壓力公式F-尸XS壓強不變，作用面積加大，壓力就變大，這樣在相同的風機轉速下，箱內的氣體壓強一致，垃圾受到的真空吸力(即壓力)就大，就容易被抽吸進垃圾箱體。此種機構清掃潮濕地面上枯枝爛葉特別有效。根據試驗結果，兩種吸嘴在相同路面作業時，新3提高滾輪的使用壽命，降低使用成本新型吸嘴尾部和車架之間裝有懸掛拉簧、調節筒和鏈條。安裝時，先調節好鏈條長度，保持拉直狀態，使前后滾輪著地。調節筒由兩端左右旋螺桿和中部套筒組成，旋轉套筒使拉伸彈簧拉長，直到彈簧拉力接近而略小于吸嘴的重力。吸掃式路面清掃車具有路面清掃范圍寬、連續工作里程長、清掃保潔效率高、適應性好等特點。由于其吸掃裝置對微細垃圾及塵埃具有良好的吸拾、除塵和輸送效果,有效減少了清掃對環境的污染,同時能滿足高等級公路快速往返和低速作業的要求,因而是高等級公路路面保潔最理想的清掃設備。 大型吸掃式清掃車采用定型汽車底盤和雙發動機驅動形式,其行走系統具有汽車行駛的獨立性和工作可靠性,同時副發動機又可滿足吸掃系統對動力的要求。掌握清掃車的關鍵應用技術,正確使用,合理維護,對保持清掃機械正常運轉、提高出勤率和延長機械使用壽命有著十分重要的作用。 合理選用吸掃裝置的結構形式國產吸掃式清掃車的吸掃裝置有4種布置形式:中置四掃盤后置吸嘴式、中置四掃盤加后置臥刷吸嘴式、前置二掃盤加中置二掃盤吸嘴式和中置二掃盤加中置臥刷雙吸嘴式。中置四掃盤后置吸嘴式清掃車是在吸收國外先進技術的基礎上,結合國內實際情況開發出的新一代路面清掃車,具有清掃視線好、易操作、清掃效果好等特點,其清掃寬度可達3.5 m,清掃速度可高達30 km/h,垃圾吸入粒度大(最大可達125 mm),掃凈度可高達97.2%,且對周圍環境污染小,最適合清掃剛性水泥或其它硬性路面。采用前置式掃盤的清掃車具有清掃直觀等優點,適合清掃城市道路和高等級瀝青路面,但在路面灰塵較多、壓塵不夠理想的情況下不宜使用,以免由于揚塵影響駕駛員視線。由于揚塵的影響,此種前置式掃盤清掃車的清掃速度受到一定限制,通常應控制在3~20 km/h。 采用中置二掃盤加中置臥刷滾掃裝置的清掃車,由于掃盤間距偏窄(清掃寬度約為2.2m)清掃能力相對較低。通常其吸入粒度較小,二次污染較大,故清掃速度不宜過高,只適宜清掃城市 道路或灰塵較少的瀝青路面兩側。根據高等級公路路面性質、路面狀況、地理環境和氣候等因素,合理選用清掃車吸掃裝置的結構及布置形式,是提高路面清掃效率的首要問題。最佳作業速度的選擇與控制如何選擇和控制清掃車主車的行駛速度和驅動清掃工作裝置的轉速,對清掃使用效能有著直接的影響。實踐證明,灰塵覆蓋量和塵埃粒度大小、路面干燥程度和濕度狀況是調節、改變行駛速度與工作轉速的主要依據。通常,由于城市道路較窄,行人和障礙較多,故清掃城市道路時,其行駛速度一般應控制在5~6 km/h；對于高等級公路路面,特別是高速路面,其清掃行駛速度應提高到5~20 km/h,保潔行駛速度則可高達15~30 km/h。 Attracts the mouth is a sweeping machine important work installment, it is sweeps into the front scanning middle the vehicles trash to transport from the ground to the trashcan in vivo one kind of trash guidance feedway.Attracts the mouth structure, the performance quality directly affects the effect which vacuums to the entire vehicle.The tradition attracts the mouth the structure more and more not to adapt the present path condition, the period of revolution one long, exposes many flaws.In order to enhance the sweeping machine to sweep clear ability, the improvement attracts the mouth structure imminently already. First, analyzes the sweeping machine to attract the mouth the structure principle.It is becomes by the four sides metal hoarding, assumes the platy, encircles with the ground has certain volume housing.The crown opens the mouth through the rubber sucker and the box body is interlinked, becomes an airtight warehouse body with the box build, front attracts the population for trash.Entire attracts the mouth body by about side and the behind rubber hoop support, the adjustment hoop organization causes to attract the mouth base to leave the ground gap is approximately 5-10mm.When work, the air blower unceasing suction, causes the closed casing body to be at the vacuum state, like this attracts the mouth peripheral to form certain negative pressure.Front gathers together by the scanning middle the vehicles trash receives the vacuum suction the attraction, is collected along the box body channel in box in vivo.When special-purpose installment knock off, attracts the mouth body to receive certain altitude through the promotion organization, guarantees the vehicles transportation travel the security.Therefore aims at attracts the mouth use and the use environment, profits from the domestic and foreign advanced sweeping machines to attract the mouth structure, attracts the mouth to the tradition. But 2 proposes business in a big way to the density, many the thousandth of a Yuan, viscousness trash suction sandy soil trash quite is wet, the post-compaction has certain adhesion to the ground, the tradition attracts the mouth to have to depend on enhances the air blower rotational speed to be able to attract cleanly.New attracts the mouth rear part addition horizontal type scanning (e.g. chart Zb) to be able to enhance sweeps clear the efficiency.The horizontal-type scanning installs in attracts behind the mouth, by 5 fixes the circular scanning on the spindle, the oil motor impetus spindle causes scanning high speed revolving.If trash has certain coherency, the vacuum suction is insufficient to overcome trash to the ground adhesion, must through the scanning trundle, cause trash to raise, the vacuum suction area of influence increases.Is invariable according to the intensity of pressure, the area of influence enlarge, the pressure increases, like this under the same air blower rotational speed, in the box gas intensity of pressure is consistent, trash receives vacuum suction (i.e. pressure) big, easily is pumped the trashcan body.This kind of organization sweeps clear in the moist ground the deadwood rotten leaf to be specially effective.According to the test result, two kinds attract the mouth when the same road surface work, new 3 enhances the hoop the service life, reduces the use cost new to attract between the mouth rear part and the frame is loaded with the hand extension spring, adjusts the tube and the chain link.When installs, adjusts the good chain link length first, the maintenance pulls the straight condition around, causes the hoop to be well-grounded.Adjusts the tube the spiral pole and middle the sleeve is composed by the both sides about, the rotating sleeve makes to stretch the spring to elongate, approaches until the spring pulling force is smaller than slightly attracts the mouth the gravity.Attracts sweeps the type road surface to sweep clear the vehicle to have the road surface to sweep clear the scope width, the continuous working course long, sweeps clear maintains cleanliness the efficiency high, the compatibility good and so on the characteristics.Because it attracts sweeps the installment has to tiny trash and the dust good attracts ascends, the dust removal and the transportation effect, reduced effectively has swept clear to the environment pollution, simultaneously could satisfy the first-class highway fast round-trip and the low speed work request, thus was the first-class highway road surface maintains cleanliness the most principle to sweep the equipment. Large-scale attracts sweeps the type to sweep clear the vehicle to use the stereotypia motor car chassis and the bimotor actuation form, its undercarriage system has the automobile travel independence and the operational reliability, simultaneously the auxiliary engine may attract satisfiedly sweeps the system to the power request.Grasping sweeps clear the vehicle the key application technology, the correct use, the reasonable maintenance, to maintains sweeps clear the machinery normal work, enhances the attendance rate and the extension machinery service life has the extremely vital role. Selects reasonably attracts sweeps the installment the structural style domestic product to attract sweeps the type to sweep clear the vehicle to attract sweeps the installment to have 4 kind of arrangement forms: Sets four sweeps the plate postpositioned to attract the mouth type, sets four sweeps the plate to add postpositioned lies brushes attracts the mouth type, pretage two sweeps the plate to add sets two sweeps the plate to attract the mouth type and sets two sweeps the plate to add sets lies brushes double attracts the mouth type.Sets four sweeps the plate postpositioned to attract the mouth type to sweep clear the vehicle is in the absorption overseas vanguard technology foundation, the union domestic actual situation develops the new generation of road surface sweeps clear the vehicle, has sweeps clear the line of sight well, easy to operate, to sweep clear the effect well and so on the characteristics, it sweeps clear the width to be possible to reach 3.5 m, sweeps clear the speed to be possible to reach as high as 30 km/h, trash inspiration granularity in a big way (may reach 125 mm most greatly), sweeps only may reach as high as 97.2%, also pollutes slightly to the environment, sweeps clear the rigid cement or other rigid road surface suitably.Uses pretage -like to sweep the plate to sweep clear the vehicle to have sweeps clear and so on the merits intuitively, sweeps clear the urban road and the high-grade bituminous pavement suitably, but are many in the road surface dust, presses in the dust insufficiently ideal situation to use not suitably, because in order to avoid raises the dust to affect the pilot's line of vision.Because raises the dust the influence, this kind of pretage -like sweeps the plate to sweep clear the vehicle to sweep clear the speed to receive certain limit, usually should control in 3~20 km/h. Uses sets two sweeps the plate to add sets lies brushes rolls sweeps the installment to sweep clear the vehicle, because sweeps the plate spacing to be narrow (sweeps clear width approximately is 2.2m) sweeps clear ability relatively low.The usual its inspiration granularity is small, two pollution is big, therefore sweeps clear the speed not to be suitable excessively high, is only suitable sweeps clear the city. Path or dust few bituminous pavement both sides.According to first-class highway factors and so on road surface nature, road surface condition, geographical environment and climate, select reasonably sweep clear the structure and the arrangement form which Che Xisao installs, is enhances the road surface to sweep clear the efficiency the most important question.How does the best work speed choice and control chooses and the control sweeps clear the vehicle owner vehicle the moving velocity and the actuation sweeps clear the work installment the rotational speed, to sweeps clear the operating effectiveness to have the direct influence.The practice proved that, the dust cover quantity and the dust granularity size, the road surface dry degree and the humidity condition are the adjustment, the change moving velocity and the work rotational speed main basis.Usually, because the urban road is narrow, the pedestrian and the barrier are many, when sweeps clear the urban road, its moving velocity should control generally in 5~6 km/h; Regarding the first-class highway road surface, specially the high speed road surface, it sweeps clear the moving velocity to be supposed to enhance to 5~20 km/h, maintains cleanliness the moving velocity to be possible to reach as high as 15~30 km/h. 8 指 導 教 師 評 語 外文翻譯成績： 指導教師簽字： 年 月 日 注：1. 指導教師對譯文進行評閱時應注意以下幾個方面：①翻譯的外文文獻與畢業設計（論文）的主題是否高度相關，并作為外文參考文獻列入畢業設計（論文）的參考文獻；②翻譯的外文文獻字?jǐn)?shù)是否達到規定數量（3 000字以上）；③譯文語言是否準確、通順、具有參考價值。 2. 外文原文應以附件的方式置于譯文之后。