槽形托輥帶式輸送機設計-DTⅡ型【傾角4度】

喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 槽形托輥帶式輸送機設計 學生姓名：張錦衛 班級：050313 指導老師：封立耀 摘要：本文中概述了帶式輸送機的應用范圍，分析了其工作原理和主要性能。對帶式輸送機的各個組成部件進行了詳細的分析和選用。在設計中對輸送機的主要部件進行了受力計算。并用Solidworks對連接軸進行有限元分析，使其強度達到要求。其后還對輸送機的主要部件的作了壽命分析。 本文所設計的是槽形托輥帶式輸送機，其設計要求為：輸送物料為原煤，輸送量：80 噸/小時，輸送長度：30 米,提升高度2米；堆積密度：900公斤/米3；物料在帶面上的動堆積角為，輸送帶速：1.2米/秒，上托輥槽形布置。設計中，其整體是一個傾斜的狀態，上托輥都采用槽形布置；下（回程）托輥采用平行托輥。本輸送機為向下運輸物料，其傾斜角為3.80<150，所以采用小傾角設計。在設計帶寬時，按照槽形布置來選擇計算。在尾架的選取方面，采用螺旋拉緊裝置尾架，使輸送帶能始終保持必要的張力。用Solidworks對連接軸進行有限元分析，得出其一般工作時的性能狀態，并做出相應的調整。 關鍵詞： 槽形托輥 帶式輸送機 輸送帶 有限元分析 指導老師簽名： The Design of Slotted Roller Belt Conveyor Student name: zhangjinwei Class: 050313 Supervisor: fengliyao Abstract: This paper provides an overview of the scope of application of belt conveyor, an analysis of its working principle and main performance. The detailed analysis and selection are carried out on the various components of the conveyor components. In the design of the conveyor of the main components of the stress is calculated. In the design bandwidth, the calculation is carried out in accordance with the layout. And Solidworks is used to do the finite element analysis on the connecting axis. Subsequently it also analysis the main conveyor components’ life. ????? What is designed in this paper is slotted roller belt conveyor, the design requirements are: transport of materials: coal, transport capacity: 80 tons / hour, transmission length: 30 meters, 2 meters high upgrade; Bulk Density: 900 kg / m3; materials in the dynamic accumulation of the surface with angle, conveyor speed: 1.2 m / s, on the trough roller arrangement. Design of a tilt the overall state of the idler trough arrangement used; under the (return) the use of parallel idler rollers. When the materials are transport down through the conveyor, the tilt angle is 3.80 <150, so take the use of small-angle design. As the selection of the tailstock, we take the use of Tailstock screw tensioning device so that the conveyor system can always maintain the necessary tension. And Solidworks is used to do the finite element analysis on the connecting axis, to meet the required strength. Keywords: slotted roller belt conveyor conveyor idlers Finite Element Analysis Signature of supervisor：