bs英國標準】bs en 1308782000 防護帽.試驗方法.電氣特性 (protective helmetstest methodselectrical properties)

《bs英國標準】bs en 1308782000 防護帽.試驗方法.電氣特性 (protective helmetstest methodselectrical properties)》由會員分享，可在線閱讀，更多相關《bs英國標準】bs en 1308782000 防護帽.試驗方法.電氣特性 (protective helmetstest methodselectrical properties)（11頁珍藏版）》請在裝配圖網上搜索。

1、 BRITISH STANDARD Protective helmets D Test methods D Part 8: Electrical properties The European Standard EN 13087-8:2000 has the status of a British Standard ICS | BS EN 1308

2、7-8:2000 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

3、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 13087-8:2000 National foreword This British Standard is the official English language version of EN 13

4、087-8:2000. The UK participation in its preparation was entrusted to Technical Committee PH/6, Head protection, which has the responsibility to: D aid enquirers to understand the text; D present to the responsible European committee any enquiries on the interpretation, or proposals for cha

5、nge, and keep the UK interests informed; D monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement i

6、nternational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled aInternational Standards Correspondence Indexo, or by using the aFindo facility of the BSI Standards Electronic Catalogue. A British Standard does not pur

7、port to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a

8、front cover, an inside front cover, the EN title page, pages 2 to 7 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amd. No. Date Comments This British Standard, having been pre

9、pared under the direction of the Health and Environment Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 December 2000 BSI 12-2000 ISBN 0 580 36445 3 Amendments issued since publication EUROPEAN STANDARD NORME EURO

10、PéENNE EUROP?ISCHE NORM EN 13087-8 October 2000 ICS English version Protective helmets - Test methods - Part 8: Electrical properties Casques de protection - Méthodes d'essai - Partie 8: Propriétés électriques Schutzhelme - Prüfverfahren - Teil 8: Elektrische

11、 Eigenschaften This European Standard was approved by CEN on 14 July 2000. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists

12、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respo

13、nsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,

14、Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I Té EUR O P éEN DE NOR M A L I S A TI ON EUR O P ? I S C H ES KOM I TEE F ü R NOR M UNG Central Sec

15、retariat: rue de Stassart, 36 B-1050 Brussels ? 2000 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13087-8:2000 E CONTENTS Foreword .....................................................................

16、...................................................... 2 Introduction ....................................................................................................................... 3 1 Scope ..................................................................................................

17、........................... 3 2 Normative references ..................................................................................................... 3 3 Terms and definitions ..................................................................................................... 3 4 Prerequisi

18、tes .................................................................................................................. 3 5 Methods ......................................................................................................................... 4 Annex A (normative) Test results – Uncertai

19、nty of measurement ................................ 6 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives .................................................................................. 7 Foreword This European

20、 Standard has been prepared by Technical Committee CEN/TC 158 "Head protection", the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2001, and conflic

21、ting national standards shall be withdrawn at the latest by April 2001. This European Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Dir

22、ective(s), see informative Annex ZA, which is an integral part of this standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, Fr

23、ance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. It consists of ten Parts as follows: Part 1 : Conditions and conditioning Part 2 : Shock absorption Part 3 : Resistance to penetration Part 4 : Retention

24、system effectiveness Part 5 : Retention system strength Part 6 : Field of vision Part 7 : Flame resistance Part 8 : Electrical properties Part 9 : Mechanical rigidity Part 10 : Resistance to radiant heat Introduction This standard is intended as a supplement to the specific product stan

25、dards for protective helmets (helmet standards). Test methods may be applicable to complete helmets or parts thereof, and may be referenced in the other helmet standards. Performance requirements are given in the appropriate helmet standard, as are such details as the number of samples, precondit

26、ioning, preparation of samples for the tests, sequence and duration of testing and assessment of test results. If deviations from the test method given in this standard are necessary, these deviations will be specified in the appropriate helmet standard. 1 Scope This European Standard des

27、cribes methods of test for protective helmets. The purpose of these tests is to enable assessment of the performance of the helmet as specified in the appropriate helmet standard. This standard specifies the methods of test for electrical properties 2 Normative references This European

28、 Standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to, or revisions of any of these publications

29、 apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 13087-1 Protective helmets - Test methods - Part 1 : Conditions and conditioning 3 Terms and

30、definitions For the purposes of this European Standard, the terms and definitions given in this European Standard may be found in the appropriate helmet standard. 4 Prerequisites In order to implement this standard, at least the following parameters shall be specified in the appropriate

31、 helmet standard: a) performance requirements b) number of samples c) preparation of samples d) sequence of conditioning e) sequence of tests f) method(s) of test - 5.3 and/or 5.4 and/or 5.5 5 Methods 5.1 General Testing shall be performed in ambient conditions specified in EN 1308

32、7-1. When the test method specifies that the helmet shall be fitted to a headform, this shall be done in accordance with the manufacturer's fitting instructions, if supplied. If none are supplied, the helmet shall be fitted so as to simulate typical fitting in use. Three test methods are speci

33、fied. The method given in 5.2 is intended to simulate closely the in-use situation - that is, the leakage current to the wearer via a live conductor touching the shell. The method given in 5.3 is dependent only upon the transverse resistance of the shell (thickness). This effectively preclude

34、s the use of a metal shell and of holes or metal fasteners passing through the shell. The method given in 5.4 is dependent only upon the surface resistance of the shell and effectively precludes the use of shells which have a conductive surface (eg metal electro-plating). This test is deemed to

35、be necessary in order to obviate the danger to the wearer should he/she try to remove a helmet whose shell is in contact with a live conductor. The method(s) to be used is/are specified in the helmet standard. 5.2 Conductive headform test 5.2.1 Principle The leakage current between

36、 the outside and inside of the complete helmet and retention system, (as supplied by the helmet manufacturer) is measured at a specified voltage, when the helmet is mounted on a metal headform. 5.2.2 Procedure Immerse the complete sample helmet and retention system in fresh tap water at room

37、temperature for a period of (15 ± 2) min. Remove the helmet from the water and allow to drain for between 1 and 2 min max. Mount the sample helmet on an appropriate sized aluminium headform, in the manner it is intended to be worn, and secure firmly with the retention system. Apply an altern

38、ating test voltage at nominally 50 Hz or 60 Hz between the aluminium headform and a suitably insulated hand-held metal probe of 4 mm diameter and with a hemispherical radiused end. Apply the probe at any point on the external surface of the helmet shell situated at, or above, its lower edge. A

39、t each test point, increase the voltage at a steady rate to (1200 ± 25) Vac within 1 min and maintain it at this value for (15 ± 2) s. Record the leakage current at this voltage to the nearest 0,1 mA, together with any evidence of breakdown. Repeat the test in order to investigate at least three

40、 test points. 5.2.3 Test report Report the leakage currents measured, together with any occurrences of breakdown. 5.3 Wet helmet insulation test 5.3.1 Principle The leakage current between the outside and inside of the helmet shell is measured at a specified voltage. 5.3.2

41、 Procedure Place th e helmet shell in a (3 ± 0,2) g/l solution of sodium chloride at a temperature of (22 ± 5) C for (24 ± 0,5) h. Remove the helmet shell, wipe it and place it upside down in a container of appropriate size. Fill the container and the helmet shell with the sodium chlor

42、ide solution, up to 10 mm below the lowest point on the lower (as worn) edge of the shell. Where necessary, adjust the orientation of the helmet shell in the sodium chloride solution in order to accommodate shells whose lower edge is not straight. Apply an alternating test voltage at nominally

43、 50 Hz or 60 Hz between an electrode immersed in the solution inside the helmet shell and another electrode in the container, outside of the helmet shell. Increase the voltage at a steady rate to (1200 ± 25) Vac within 1 min and maintain it at this value for (15 ± 2) s. Record the leakage curren

44、t at this voltage to the nearest 0,1 mA, together with any evidence of breakdown. 5.3.3 Test report Report the leakage currents measured, together with any occurrences of breakdown. 5.4 Surface insulation test 5.4.1 Principle The leakage current between any two points on the su

45、rface of the helmet shell is measured at a specified voltage. 5.4.2 Procedure Ensure that the shell of the helmet is dry before the test. Apply an alternating test voltage at nominally 50 Hz or 60 Hz between two suitably insulated hand-held metal probes of 4 mm diameter and with hemispheri

46、cal radiused ends. Apply the probes to any two points on the surface of the helmet shell (inside and/or outside) located not closer than 20 mm to each other. At each test point, increase the voltage at a steady rate to (1200 ± 25) Vac within 1 min and maintain it at this value for (15 ± 2) s.

47、 Record the leakage current at this voltage to the nearest 0,1 mA, together with any evidence of breakdown. Repeat the test in order to investigate at least three test points. 5.4.3 Test report Report the leakage currents measured, together with any occurrences of breakdown.

48、 Annex A (normative) Test results – Uncertainty of measurement For each of the required measurements performed in accordance with this standard, a corresponding estimate of the uncertainty of measurement shall be evaluated. This estimate of uncertainty shall be applied and stated when reporting

49、 test results, in order to enable the user of the test report to assess the reliability of the data. Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives This European Standard has been prepared under a mand

50、ate given to CEN by the European Commission and the European Free Trade Association and supports essential requirements of EU Directive on personal protective equipment (PPE) 89/686/EEC. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within th

51、e scope of this standard. The following clauses of this standard are likely to support requirements of Directive 89/686/EEC: EU Directive 89/686/EEC, Annex II Clause of this standard 1.2.1 Absence of risks and other inherent nuisance factors 5 3.8 Protection against electric shock 5 Co

52、mpliance with the clauses of this standard provides one means of conforming with the specific essential requirements of the Directive concerned and associated EFTA regulations. BS EN 13087-8:2000

53、 BSI 389 Chiswick High Road London W4 4AL  | | | | | | | | | BSI D British Standards Institution | | | | | | | BSI is the independent national body responsible for preparing British Standards. It | | | presents the UK view on standards in E

54、urope and at the international level. It is | incorporated by Royal Charter. | | | Revisions | | | British Standards are updated by amendment or revision. Users of British Standards | | should make sure that they possess the latest amendments or editions. | | It is the constant aim

55、 of BSI to improve the quality of our products and services. We | | | would be grateful if anyone finding an inaccuracy or ambiguity while using this | | British Standard would inform the Secretary of the technical committee responsible, | the identity of which can be found on the inside

56、 front cover. Tel: 020 8996 9000. | | Fax: 020 8996 7400. | | | BSI offers members an individual updating service called PLUS which ensures that | subscribers automatically receive the latest editions of standards. | | | Buying standards | | | | Orders for all BSI, internationa

57、l and foreign standards publications should be | addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. | | | In response to orders for international standards, it is BSI policy to supply the BSI | | implementation of those that have been published as British Standards, u

58、nless | otherwise requested. | | | Information on standards | | | | BSI provides a wide range of information on national, European and international | standards through its Library and its Technical Help to Exporters Service. Various | | BSI electronic information services are also

59、 available which give details on all its | | products and services. Contact the Information Centre. Tel: 020 8996 7111. | Fax: 020 8996 7048. | | | | Subscribing members of BSI are kept up to date with standards developments and | | receive substantial discounts on the purchase price

60、 of standards. For details of | these and other benefits contact Membership Administration. Tel: 020 8996 7002. | | Fax: 020 8996 7001. | | | Copyright | | Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of | | | the publications of the interna

61、tional standardization bodies. Except as permitted | | under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, | stored in a retrieval system or transmitted in any form or by any means ± electronic, | | photocopying, recording or otherwise ± without prior written

62、 permission from BSI. | | | This does not preclude the free use, in the course of implementing the standard, of | necessary details such as symbols, and size, type or grade designations. If these | | | details are to be used for any other purpose than implementation then the prior | w

63、ritten permission of BSI must be obtained. | | | If permission is granted, the terms may include royalty payments or a licensing | | agreement. Details and advice can be obtained from the Copyright Manager. | | Tel: 020 8996 7070. | | | | | | | | | | | | | | | | | | | | | 國內外標準大全 豆丁網國內外標準下載地址 httkmust1