【BS英國標準】BS EN 52411997 Steel strip sheaths for prestressing tendons – Test methods

《【BS英國標準】BS EN 52411997 Steel strip sheaths for prestressing tendons – Test methods》由會員分享，可在線閱讀，更多相關《【BS英國標準】BS EN 52411997 Steel strip sheaths for prestressing tendons – Test methods（10頁珍藏版）》請?jiān)谘b配圖網上搜索。

1、 國內外標準 大全 豆丁網國內外標準下載地址 BRITISH STANDARD Steel strip sheaths for prestressing tendons D Test methods Part 1. Determination of shape and dimensions The European Standard E

2、N 524-1 : 1997 has the status of a British Standard ICS 77.140.75; 91.080.40 | BS EN 524-1 : 1997 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |

3、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 524-1 : 1

4、997 National foreword This British Standard is the English language version of EN 524-1 : 1997. The UK participation in its preparation was entrusted by Technical Committee B/525, Building and civil engineering structures, to Subcommittee B/525/2, Structural use of concrete, which has t

5、he responsibility to: ± aid enquirers to understand the text; ± present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; ± monitor related international and European developments and promulgate t

6、hem in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the

7、 section entitled `International Standards Correspondence Index', or by using the `Find' facility of the BSI Standards Electronic Catalogue. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary

8、of pages This document comprises a front cover, an inside front cover, an EN title page, pages 2 to 4, an inside back cover and a back cover. Amd. No. Date Text affected This British Standard, having been prepared under the direction of the Sector Board for Buil

9、ding and Civil Engineering, was published under the authority of the Standards Board and comes into effect on 15 November 1997 BSI 1997 ISBN 0 580 28666 5 Amendments issued since publication EUROPEAN STANDARD EN 524-1 NORME EUROPE? ENNE EUROPAè ISCHE NORM March 1997

10、 ICS 77.140.75; 91.080.40 Descriptors: Prestressed concretes, tubes, sheathing, prestressing steels, classifications, specification, verifications, marking English version Steel strip sheaths for prestressing tendons D Test methods D Part 1: Determination of shape and dimensions

11、 Gaines en feuillard d'acier pour ca? bles de pre? contrainte D Me? thodes d'essai D Partie 1: De? termination de la forme et des dimensions Huè llrohre aus Bandstahl fuè r Spannglieder D Pruè fverfahren D Teil 1: Ermittlung der Formen und Ma?e This European Stand

12、ard was approved by CEN on 1997-01-27. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referen

13、ces concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN

14、 member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway

15、, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comite? Europe? en de Normalisation Europaè isches Komitee fuè r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 Copyright reserved to CEN

16、 members.  Ref. No. EN 524-1 : 1997 E Page EN 524-1 : 1997 BSI 1997 Foreword This European Standard has been prepared by Technical Committee CEN/TC 104, Concrete Contents  Page (performance, production, placing and compliance criteria), the Secretar

17、iat of which is held by DIN. 1 Scope 3 2 Normative references 3 3 Apparatus and accuracy 3 4 Internal diameter, height of profile and wall thickness of sheaths 3 5 Relative volume of profile 3 This standard is a part of the series EN 524 Sheaths for prestressing tendons D Tes

18、t methods which additionally comprises the following Parts ± Part 2 Determination of flexural behaviour ± Part 3 To-and-fro bending test ± Part 4 Determination of lateral load resistance ± Part 5 Determination of tensile load resistance ± Part 6 Determination of leaktightne

19、ss (Determination of water loss) These European standards apply to EN 523 Steel strip sheaths for prestressing tendons D Terminology, requirements, quality control. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo

20、rsement, at the latest by September 1997, and conflicting national standards shall be withdrawn at the latest by September 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Au

21、stria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Foreword 2 Page 3 EN 524-1 : 1997 1 Scope This European Standard specifies the proce

22、dure for determining the shape and dimensions of sheaths for prestressing tendons which comply with EN 523. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate pla

23、ces in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these 5 Relative volume of profile A test specimen with a length of at least l = 500 mm1) shall be sealed at one end so that it is watertight. The total volume Vt

24、ot of the hollow space inside the specimen shall be determined by filling the specimen with water and then measuring the content (see figure 2). The volume Vref and the surface area Aref of the reference cylinder shall be calculated from the mean internal diameter d1 as described in clause

25、4 and the length l of the test specimen. The relative volume of the profile (Vrel) measured in cm3/cm2 is calculated using the following equation: Vtot 2 Vref publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the l

26、atest edition of the publication referred to applies. Vrel = where Aref EN 523 Steel strip sheaths for prestressing tendons D Terminology, requirements, quality control 3 Apparatus and accuracy ± A possible test device is shown in figure 2 ± The procedure to determine the re

27、lative volume of profile (Vrel) shall allow for an accuracy of 5 % ± Vernier calliper (accuracy of 0,1 mm) ± Micrometer gauge (accuracy of 0,01 mm) 4 Internal diameter, height of profile and wall thickness of sheaths The internal diameter, d1, and the height of profile, h, shall be determi

28、ned by means of a vernier calliper using the specimen described in clause 5. Measurements shall be taken at both ends of the specimen in two directions at right angles to one another (see figure 1) before the specimen is sealed. The mean values shall be calculated from the values obtained. Th

29、e wall thickness shall be measured by a micrometer gauge at least at four different points. Aref (= 3 d1 3 l) is the surface area of the reference cylinder (in cm2); Vref is the volume of the reference cylinder (in cm3); Vtot is the volume of water in the specimen (in cm3).

30、 Figure 1. Internal diameter, height of profile and wall thickness of sheaths 1) It is recommended that the specimen length chosen is such that the specimen can be used for the other test. BSI 1997 Page EN 524-1 : 1997

31、 Figure 2. Test set-up for determining the total volume BSI 1997 blank

32、 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | BSI D British Standards Institution | | | | | | | BSI is the independent national body responsible for

33、 preparing British Standards. It | | | presents the UK view on standards in Europe and at the international level. It is | incorporated by Royal Charter. | | | Revisions | | | British Standards are updated by amendment or revision. Users of British Standards | | should make sure t

34、hat they possess the latest amendments or editions. | | It is the constant aim of BSI to improve the quality of our products and services. We | | | would be grateful if anyone finding an inaccuracy or ambiguity while using this | | British Standard would inform the Secretary of the tech

35、nical committee responsible, | the identity of which can be found on the inside front cover. Tel: 020 8996 9000. | | Fax: 020 8996 7400. | | | BSI offers members an individual updating service called PLUS which ensures that | subscribers automatically receive the latest editions of sta

36、ndards. | | | Buying standards | | | | Orders for all BSI, international and foreign standards publications should be | addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. | | | In response to orders for international standards, it is BSI policy to supply the BS

37、I | | implementation of those that have been published as British Standards, unless | otherwise requested. | | | Information on standards | | | | BSI provides a wide range of information on national, European and international | standards through its Library and its Technical Help t

38、o Exporters Service. Various | | BSI electronic information services are also available which give details on all its | | products and services. Contact the Information Centre. Tel: 020 8996 7111. | Fax: 020 8996 7048. | | | | Subscribing members of BSI are kept up to date with stan

39、dards developments and | | receive substantial discounts on the purchase price of standards. For details of | these and other benefits contact Membership Administration. Tel: 020 8996 7002. | | Fax: 020 8996 7001. | | | Copyright | | Copyright subsists in all BSI publications. BSI

40、also holds the copyright, in the UK, of | | | the publications of the international standardization bodies. Except as permitted | | under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, | stored in a retrieval system or transmitted in any form or by any means ±

41、 electronic, | | photocopying, recording or otherwise ± without prior written permission from BSI. | | | This does not preclude the free use, in the course of implementing the standard, of | necessary details such as symbols, and size, type or grade designations. If these | | | detai

42、ls are to be used for any other purpose than implementation then the prior | written permission of BSI must be obtained. | | | If permission is granted, the terms may include royalty payments or a licensing | | agreement. Details and advice can be obtained from the Copyright Manager. | | Tel: 020 8996 7070. | | | | | | | | | | | | | | | | | | | | |