隨車起重運輸車舉升機構設計帶開題報告.zip
隨車起重運輸車舉升機構設計帶開題報告.zip,起重,運輸車,舉升機,設計,開題,報告
附錄 1:外文翻譯
隨車起重裝置的結構與設計
相對傳統的舉升機構,該舉升機構只采用了液壓缸,使液壓系統的管路簡單,控制方便,液壓系統的可靠性高,且安裝方便。上述的分析與計算,為該機構建立了結構與性能等參數間的數學關系。有關推銷與套筒間的摩擦與磨損,套筒導槽角和翻轉角度與舉升高度的適應性等問題,將有待進一步的分析研究和結構發。
隨車起重裝置在國外稱為隨車吊 。本文按國家標準稱其為隨車起重裝置。一輛安裝了隨車起重裝置的廂式貨車在貨物運輸中, 不僅顯示其防雨防塵的專有功能,而且在貨物的裝卸方面實現了機械化。
1 隨車起重裝置的發展
隨車起重裝置的發展, 在國外大體上可分為四個時期。第一代產品產生于本世紀
30 年代末, 其特點主要是單缸舉升, 而欄板翻轉靠手動, 起升質量為500kg 左右, 欄板(又稱載物平臺) 觸地傾角9°~ 10°。目前, 這種產品在東南亞、日本仍在使用, 90 年代, 還在美國得到了新的發展。第二代產品產生于50 年代初的歐洲市場, 在第一代產品的基礎上增加了翻轉關門油缸。舉升與翻轉分別由二個獨立油缸實現。最常見的是四只油缸的型式, 也有雙缸的。起升質量在500 kg 以上, 載物平臺觸地傾角10°, 翻轉動作憑操作者經驗控制。該種產品目前主要用于美洲及東南亞地區。第三代產品產生于70 年代末的歐洲市場, 是在第二代產品的基礎上增加第五只油缸。這只油缸在液壓系統中主要起相對位置的記憶功能, 使載物平臺觸地、離地的翻轉動作不再由操作者控制而由液壓系統本身控制, 從而使升降過程相對平穩與安全。觸地傾角一般為8°~
10°。若兼作廂門用, 因平臺尺寸增大, 傾角也可能小于8°。目前該類產品普遍用于歐美地區。第四代產品產生于90 年代初, 其液壓系統及功能原理同第三代產品, 只增加了記憶油缸的尺寸, 使記憶動作的范圍進一步增大。它不同于第三代產品的關鍵在于其載物平臺增加特殊結構, 由一體改為兩體活動聯接, 使平臺觸地后不僅能自動翻轉, 而且有一個下沉的動作, 使觸地傾角達到6°, 甚至在6以下。目前該產品在荷蘭、南斯拉夫和中國已申請了實用新型發明專利。國內已有定型產品投放市場。從操作性能、安全可靠性等使用效果上, 第四代產品將逐漸取代了第二、三代產品。而第一代產品, 由于其結構簡單, 重量輕, 雖然技術含量低, 但具有便于維修等優點, 在發展中國家將仍有一定的市場。隨車起重裝置在國內的發展只是近十幾年的事情。1985 年原郵電部從日本進口了一批裝有隨車起重裝置的廂式車。此后, 由漢陽專用汽車研究所、湖北汽車配件廠和郵電部明水通信機械廠三家合作進行了國產化研制開發, 歷時兩年多,
卻因多種原因而未能投入使用。1988 年初, 郵電部明水通信機械廠組織技術人員, 繼續研制。在北京市郵政局的大力協助下, 經過近四年的努力, 產品質量日漸趨于穩定。國產化產品早期用汽車發動機作為動力。1992 年實現以汽車蓄電池作為液壓泵站的驅動力。1992 年以后, 隨車起重裝置因國內廂式車的發展而開始發展起來, 技術水平也逐漸向國際靠近。據目前了解的情況, 國內生產欄板起重裝置的企業包括明水郵電通信設備廠等至少有5 家, 產品結構型式有單缸、四缸、五缸及90 年代初的美國技術及最新型的五缸技術。盡管在產品結構形式上, 國際上的四代產品均在國內都有生產, 但就其發展而言, 仍處于起步階段。國內市場的擴展, 還需要間與機遇。從時間上講可能不會太久, 從品種上講, 短時期內將仍是以多種型式并存, 但最終可能是單缸產品和五缸產品為主。
2 隨車起重裝置的基本原理
隨車起重裝置的品種雖多,但其基本原但其基本原理卻是相同的,即平行四連桿機構的平行移動原理實際應用中, 是兩組平行的四連桿機構,分置于汽車縱梁兩側, 同步動作, 而DCE 即為上文所說的載物平臺(欄板)。設計時,須解決以下三個問題:BC桿轉動的動力; BC桿轉動動力的作用點及作用形式;CD 桿在C 點觸地后, 必須有一個繞D 點轉動動作,以便E端觸地,方便貨物裝卸。
2.1 動力系統
隨車起重裝置在發展初期為汽車發動機通過取力器帶動油泵驅動。由于工作時發動機需要怠速運轉, 現已很少采用。目前基本都采用微型液壓泵站驅動, 以汽車電瓶為動力源。微型泵站的基本構成有直流電動機(與汽車電瓶電壓匹配)、控制閥、齒輪泵、組合閥體(溢流、單向節流) 以及油箱、電機啟動開關、控制開關等。根據汽車電瓶電壓不同, 直流電機有12 V、24 V 兩種, 功率根據起重量不同有018 kW、110 kW、112
kW、115 kW、2 kW、3 kW 等。齒輪泵根據油缸數量(主要是液壓流量) 和液壓系統工作壓力選擇, 排量有1 m l、112 m l、116 m l、210 m l、215 m l、410 m l 多種規格, 齒輪泵最大輸出壓力可達25M Pa。液壓泵站國際產品的質量已很穩定, 國內產品質量稍差, 主要是電磁閥質量不過或體積偏大。
2.2 動力傳遞形式及作用點
動力均靠液壓油經過壓力系統由油缸傳遞到B C 桿上。油缸數量和安裝位置不同, 以及采取的D C 桿的轉動方式的差異, 其動力傳遞的路線也不同。a1 單缸對中前置。鉸鏈B 為一長轉軸, 兩平行四連桿機構安裝于軸的兩端, 軸的中間連一轉臂, 接油缸活塞桿端, 油缸另一端固定于支架上, 力的傳遞為: 油缸→轉臂轉軸→B C 桿, 工作過程如圖2。b1 單缸對中后置。油缸位于兩四連桿機構的中間位置, 兩四連桿的B C 桿
在中間用橫梁固定連為一體, 梁中間與油缸活塞桿聯接, 油缸另一端與支架聯接。c1 四缸及五缸型式。五缸結構中的第五缸是液壓記憶缸, 在液壓回路中, 只參與載物平臺觸地后平臺的翻轉動作, 而不參平臺升降, 其基本結構與四缸相同。四缸結構中B C 桿均為油缸, 這是不同于單缸的區別。
2.3 CD 桿的轉動
CD 桿的轉動, 四缸與五缸型式依靠油缸的收縮實現, 單缸對中后置式, CD 桿無法實現轉動(但可在最高位置實現翻轉, 因結構較復雜, 在此不作介紹) ; 對于單缸對中前置式, 是以B C 桿的結構改變實現的。實際設計中,A D 桿也需要作一定的技術處理才能滿足要求。另外還要注意一點,D CE 只在D 點鉸接, 其它型式為D、C 兩點鉸接。
3 隨車重裝置技術參數的確定
隨車起重裝置的技術參數主要有: 額定起升質量、升降行程、升降速度、桿件尺寸、平臺尺寸、電動機工作電壓及功率、齒輪泵排重(額定輸出流量)、控制閥型式及數量和油缸的缸徑及工作行程、額定工作壓力等。一般情況下, 設計開始時已知的參數為地板距地高度、電瓶電壓及容量、汽車縱梁間距及縱梁高度和汽車后懸尺寸等。已知參數是進行設計的基本依據。
34
附錄2:外文原文
Steeplechase lifting device structure and design
Lifting Gear steeplechase and design of the structure of the lifting mechanism is relatively traditional, the tail plate lifting mechanism using only a single fuel tank, so that the hydraulic system of the pipe is simple, convenient control and high reliability of the hydraulic system, and and ease of installation. The above analysis and calculation of the institutions such as the structure and properties of the mathematical relationship between parameters. To promote inter-related with the sleeve of the friction and wear, the sleeve guide groove angle and flip angle and a high degree of adaptability, such as lifting will be subject to further research and the analysis of the structure of hair[17].
Lifting Gear steeplechase vehicle movements in foreign countries as the rear door (end plate), its installed in the car named after the tail. In this paper, according to national standards call a lifting gear steeplechase. Steeplechase a lifting device installed on the van in the carriage of goods, not only to demonstrate its proprietary water-resistant dust-proof function, but also in the loading and unloading of goods mechanization achieved.
1. steeplechase development Lifting Gear
Lifting Gear steeplechase development, largely in foreign countries can be divided into four periods. The first generation of products in the 30's at the end of this century, characterized mainly lifting cylinder, and the steeplechase manually turned on, from or about the quality of 500kg, steeplechase (also known as loading platforms) touchdown angle 9 ° ~ 10 °. At present, this product in South-East Asia, Japan still in use, 90 years, is still the United States by the new development. Second-generation products in the early 50's the European market, in the first generation of products based on the increase of turnover to close the fuel tank. Lift and flip the fuel tank by two to achieve independence. The most common is a type 4 tank, but also of the double. Lifting the quality of more than 500 kg, platform loading touchdown angle 10 °, flip action control based on the experience of the operator. The products are mainly used in the Americas and Southeast Asia. Third-generation products in the 70's at the end of the European market is the second generation of products based on the increase in the fuel tank of the fifth. Only the fuel tank of the hydraulic system in the relative positions of the main effect of memory function, so that touchdown to loading platform, off the flip action is no longer controlled by the operator by the hydraulic control system itself, so that the process is relatively smooth take-off and landing and security. Touchdown angle is generally 8 ° ~ 10 °. If it doubles as a car door, and a result of increased platform size, angle may also be less than 8 °. At present these products to Europe and America in general. Fourth-generation products during the early 90s, and its hydraulic system and function of principles with the third-generation products, only an increase of the fuel tank the size of memory, so memory and increase the scope of action. It is different from the third generation of the product lies in the loading platform to increase its special structure, from one body to two activities connected to the platform after the touchdown, not only can automatically flip, but there is a sinking action to
achieve the touchdown angle 6 °, even in 6 below. At present, the products in the Netherlands, Yugoslavia and China has applied for a utility model patent. The domestic market has been stereotyped. From the performance, security, reliability results, the fourth-generation products will be gradually replaced the second and third generation products. The first generation of products, because of its simple structure, light weight, although the technical content, but with the advantages of easy maintenance, etc., in developing countries will still have a certain market. Lifting Gear steeplechase development in China only a few things more than a decade. The former Ministry of Posts and Telecommunications in 1985 imported from Japan with a number of lifting devices steeplechase van. Since then, by the Special Purpose Vehicle Institute of Hanyang, Hubei auto parts plant and Communication Ministry of Posts and Telecommunications Machinery Factory Mingshui three cooperation made the research and development, which lasted more than two years, due to various reasons can not be put into use. In early 1988, Ministry of Posts and Telecommunications Communications Machinery Factory Mingshui technical staff, continue to develop. Post Office in Beijing to help the strong, thanks to the efforts of the past four years, increasing product quality stabilized. Early use of domestic products as a driving force for car engines. To achieve in 1992 a car battery as the driving force of the hydraulic pump station. After 1992, lifting gear steeplechase van due to the development of domestic and began to develop, the skill level is gradually close to the international. According to the current understanding of the situation, the domestic production steeplechase of the enterprises, including Lifting Gear Mingshui, such as posts and telecommunications equipment factory at least five, the product structure have a single-cylinder, four-cylinder, five-cylinder and the early 90's and the latest U.S. technology-based The five-cylinder technology. Although the product mix in the form, the international four-generation products are produced in China, but its development is still in its infancy. The expansion of the domestic market, but also the need for inter-and opportunities. Speaking time may not last long, from the varieties of speaking, a short period of time will still exist a variety of forms, but in the end may be the single-cylinder and five-cylinder products.
2. steeplechase of the basic principles of lifting gear
Lifting Gear steeplechase varieties are numerous, but the basic fundamental tenets of the original but it is the same, that is, parallel four-bar linkage of the practical application of the principle of parallel move, it is two sets of parallel four-bar linkage, sub-put longeron on both sides of car, synchronous movements, while the DCE is the above mentioned loading platform (steeplechase). Design, the following three issues to be resolved: BC under the driving force for rotation; BC under the role of rotational dynamics and the role of the form of points; CD under the C-point after touchdown, there must be a rotationaround the point D moves to E end of touchdown to facilitate loading and unloading of goods.
2.1 Power System
Steeplechase early in the development of lifting devices for the automotive engine through the oil pump driven from power-driven devices. Working hours as a result of the need to idle the engine running, is now seldom used. At present, the basic use of micro-driven hydraulic pump station, a car battery for power source. Micro-pump station
has the basic components of DC motors (with the car battery voltage to match), control valves, gear pumps, combination valve (overflow, cutting one-way), and the fuel tank, electric start switch, control switch and so on. According to different vehicle battery voltage, DC motors are 12 V, 24 V are two different power according to the weight since there are 018 kW, 110 kW, 112 kW, 115 kW, 2 kW, 3 kW and so on. Gear pump according to the number of tanks (mainly hydraulic flow) and the hydraulic system pressure to choose, there is displacement 1 ml, 112 ml, 116 ml, 210 ml, 215 ml, 410 ml wide range of specifications, the maximum output pressure gear pump up to 25M Pa. Hydraulic Pump Station has been the international product quality is stable, less quality of domestic products, mainly the quality of the solenoid valve or volume too large, however.
2.2 The form and the role of driving force transmission point[18]
Both rely on power through the pressure of hydraulic oil system from the fuel tank to the BC transmission poles. Fuel tanks and installation of the number of different positions, and to take the DC bar the difference in the rotation, the power transmission lines are also different. a1 cylinder on the front. Hinge for a long shaft B, the two parallel four-bar linkage mounted on the shaft at both ends, a shaft connected to the middle arm, then the fuel tank of the piston rod end of the fuel tank on the other side of the fixed bracket on the transmission of power as follows: oil tumbler cylinder → → BC rod shaft, the working process in Figure 2. b1 on the rear cylinder. The fuel tank 24 is located in the middle of linkage, the two four-bar linkage in the middle of the BC bar with fixed beams together, the middle beam connecting rod and the fuel tank, fuel tank connected to the other side with the stent. c1 four-cylinder and five-cylinder type. Five-cylinder structure of the memory of the fifth hydraulic cylinder is a cylinder in the hydraulic circuit, the loading platform to participate in only touchdown after the reversal platform action, without reference platform for take-off and landing, and its basic structure with the same four-cylinder. Four-cylinder under the structure of the fuel tank of BC, which is different from the distinction between single-cylinder.
2.3 CD under the rotation
CD of the rotation pole, four-cylinder with five-cylinder fuel tank of the type of contraction depend on the realization of single-cylinder rear-mounted on, CD can not be achieved under rotation (but can be reversed to achieve at the highest position, because the structure of more complex, and I shall not introduce) ; for the single-cylinder front-on, based on the structural changes under BC achievable. The actual design, AD is also required under certain technical processing to meet the requirements. In addition, note that, D CE articulated only in the D point, the other type for the D, C two hinged.
3s t e e p l e c h a s e l i f t i n g d e v i c e t o d e t e r m i n e t h e t e c h n i c a l p a r a m e t e r s Lifting Gear steeplechase main technical parameters: Rated lifting the quality of travel movements, take-off and landing speed, shot size, platform size, operating voltage and power motor, gear pump row weight (rated output flow), control valves, the type and quantity of and the fuel tank of the bore and stroke, rated working pressure. Under normal circumstances, the beginning of the design parameters are known to width and height from the floor, battery voltage and capacity, beam spacing and beam auto height and size of rear o v e r h a n g . K n o w n p a r a m e t e r s a r e t h e f u n d a m e n t a l b a s i s f o r d e s i g n .
任務書
論文(設計)題目:隨車起重運輸車舉升機構設計
工作日期:2017年12月18日 ~ 2018年05月18日
1.選題依據:
隨車起重車是一種集起重、運輸為一體的新型高效起重運輸裝備,廣泛適用于交通運輸、電信電力、油田碼頭、市政園林等領域,目前國外隨車起重車技術相對成熟, 隨車吊價格偏高,但產品質量與性能也較為穩定,而國內市場產品單一,技術水平也相對落后。目前,國內企業產品型號以中小噸位為主,不僅品種少,而且產量低。隨車起重車的設計和開發,可以彌補其不足。增加產品種類,適應不同場所的工作需要。
2.論文要求(設計參數):
(1)隨車起重車不同結構形式的比較;
(2)選取合適的車身結構形式;
(3)對液壓舉升機構等部件進行設計;
3.個人工作重點:
(1)隨車起重車不同結構形式的比較;
(2)選取合適的車身結構形式;
(3)對液壓舉升機構等部件進行設計;
(4)利用CATIA軟件建立三維模型。
4.時間安排及應完成的工作:
第1周:理解設計題目,查找參考資料; 第2周:整理參考文獻,撰寫文獻綜述; 第3周:撰寫開題報告,翻譯英文文獻; 第4周:修改開題報告,準備開題答辯;
第5周:研究隨車起重車的設計步驟與設計方法; 第6周:完成車輛的總體布置;
第7周:對液壓舉升機構等部件進行設計; 第8周:進行中期檢查;
第9周:對液壓舉升機構進行校核; 第10周:利用CATIA軟件進行繪圖; 第11周:利用CATIA軟件進行繪圖;
第12周:完善設計內容,完成大部分圖紙,并撰寫設計說明書; 第13周:撰寫修改并完善設計說明書;
第14周:撰寫并修改畢業論文,準備畢業論文答辯。
5.應閱讀的基本文獻:
[1]王忠元,王鑫,滕儒民,李靖.隨車起重機回轉支承優化設計.起重運輸機械,2013 [2]黃飛.隨車起重機結構設計優化與仿真研究.合肥工業大學,2015 [3]崔婷婷.某型號隨車起重機設計.湖南農機,2014 [4]楊路.隨車起重運輸車臂架設計要素.商用汽車,2012 [5]胡榮.多功能車隨車起重機的設計與研究.湖南大學,2015 [6]王艷宜,張森林,鄭華,梁鵬.隨車起重機吊臂結構的有限元分析及優化.農機使用與維 修,2015-07-29 16:22
[7]管坐輦.隨車起重機結構分析與優化.吉林大學,2013-05-01 [8]羅軍.隨車起重機液壓系統研究與優化.長安大學,2014-05-25 [9]楊明星,晉民杰,范英,張帥,馬俊.折臂式隨車起重機底座有限元分析.起重運輸機械
,2014-07-20
[10]吳衛萍.隨車起重機吊臂結構分析與優化.華南理工大學,2015-10-18
[11]Rui Xue Zhao,Zeng Hai Shan,Hong Gang Ding,Hai Yan Zhang,Lei Zhu,Xue Feng Li.Reliability Analysis on Anti-Overturning Stability for Truck Crane.Trans Tech,2014
[12]V. V. Panasyuk,I. P. Vas'kiv,V. I. Kovalenko.Necessity of taking crack resistance into consideration in designing and building the units of truck-mounted cranes.Springer Journal,2013 [13]Anonymous.Liebherr truck-mounted crane provides travelling benefits.ProQuest,2014 [14]Thomas Berry.The truck-mounted shovel and dragline.ProQuest,2013
[15]Zhi Wei Chen,Zhe Cui,Yi Jin Fu,Wen Ping Cui,Li Juan Dong,Wen Guang Jiang.Structural Optimization of the Telescopic Boom of a Certain Type of Truck-Mounted Crane.Trans Tech,2014
指導教師簽字:
XX
教研室主任意見:
同意
簽字:XX 2017年12月14日
教學指導分委會意見:
同意
簽字:XX 2017年12月15日 學院公章
畢業論文(設計
)進度檢查表
第
-1
周
工作進展情況
查閱各種資料,了解本設計的意義、國內外發展現狀及發展趨勢,撰寫開題報告和文獻綜述。
2018年03月24日
指導教師意見
查閱了一定數量的參考文獻,完成了文獻綜述和開題報告,可以參加開題答辯。
指導教師(簽字):XX 2018年03月13日
第 2
周
工作進展情況
查閱資料,研究隨車起重車的設計步驟與設計方法,并開始進行論文的設計工作。
2018年03月24日
指導教師意見
研究隨車起重車的設計步驟與設計方法,開始進行隨車超重車的設計工
作。
指導教師(簽字):XX 2018年04月18日
第 4
周
工作進展情況
網上查閱相關資料,選擇相關參數,初步確定相關尺寸,完成液壓機的
選擇
2018年04月17日
指導教師意見
查閱相關資料,選擇相關參數,初步確定了相關尺寸,完成液壓機的選
擇。
指導教師(簽字):XX 2018年04月18日
第 6
周
工作進展情況
完成所有有關數據的計算,并完成校核,撰寫論文初稿,并開始繪圖
2018年04月17日
指導教師意見
完成相關設計的計算與校核,可以利用CATIA開始繪圖了。
指導教師(簽字):XX 2018年04月18日
第 8
周
工作進展情況
論文初稿撰寫完成,完成大部分零件的CATIA繪圖,并準備開始修改論
文
2018年05月17日
指導教師意見
完成大部分零件的CATIA繪圖,撰寫并準備開始修改論文.
指導教師(簽字):XX 2018年05月21日
第 10
周
工作進展情況
完成所有零件的CATIA繪圖,完成論文初稿的改重,準備答辯相關工作
2018年05月17日
指導教師意見
完善修改論文,調整論文整體結構,按論文格式規范修改。準備答辯相關材料。
指導教師(簽字):XX 2018年05月21日
過程管理評價表
評價內容
具體要求
總分
評分
工作態度
態度認真,刻苦努力,作風嚴謹
3
3
遵守紀律
自覺遵守學校有關規定,主動聯系指導教師,接受指導
3
3
開題報告
內容詳實,符合規范要求
5
4
任務完成
按時、圓滿完成各項工作任務
4
3
過程管理評分合計
13
過程管 理評語
該生在進行畢業設計的過程中,對待畢業設計工作態度認真
,努力鉆研學習與畢業相關的內容,工作作風嚴謹。能夠自覺遵守學校有關規定,主動聯系指導教師,主動通過到校、網絡、電話等方式與指導教師溝通,虛心接受指導。開題報告結構合理,內容詳實,條理清晰,計劃合理,研究方法可行,符合規范的要求。按時
、按部就班地完成了任務書中規定的工作任務,完成了隨車起重運輸車的舉升機構的設計,并較規范地完成了畢業論文。該生做事認真,樂于助人,希望在以后的工作中再接再厲,取得好成績。
指導教師簽字:XX 日期:2018-05-20
指導教師評價表
評價內容
具體要求
總分
評分
選題質量
符合培養目標要求,有一定的研究?jī)r(jià)值和實踐意義,有一定的開拓性、創新性,深度、難度適宜,工作量飽滿
5
4
能力水平
有較強的綜合運用知識能力、科研方法運用能力、中文表達與外語能力、文獻資料檢索能力、計算機應用能力
5
4
完成質量
文題相符,概念準確,分析、論證、計算、設計、實驗等正確合理,結論明確;論文結構、撰寫格式、圖表等符合基本規
10
8
指導教師評分合計
16
指導教 師評語
XX同學以《隨車起重運輸車舉升機構設計》為題,對專用車輛中的隨車起重運輸車的舉升機構進行設計,對機械臂的設計具有一定的研究?jī)r(jià)值和實踐意義。選題的深度、難度適宜,工作量較飽滿。從畢設的過程來看,該生具有較強的綜合運用知識的能力
,具有較強的科研能力、文獻檢索及計算機應用能力。從論文的完成質量來看,論文文題相符,分析、計算、設計等基本正確,論文結構合理,但撰寫格式、公式的編排與文字的字體等還需進一步規范。
指導教師簽字:XX 日期:2018-05-20
評閱人評價表
評價內容
具體要求
總分
評分
選題質量
符合培養目標要求,有一定的研究?jī)r(jià)值和實踐意義,有一定的
開拓性、創新性,深度、難度適宜,工作量飽滿
5
4
能力水平
有較強的綜合運用知識能力、科研方法運用能力、中文表
達與外語能力、文獻資料檢索能力、計算機應用能力
5
4
完成質量
文題相符,概念準確,分析、論證、計算、設計、實驗等正確
合理,結論明確;論文結構、撰寫格式、圖表等符合基本規
10
7
評閱人評分合計
15
評閱人 評語
論文完成隨車起重運輸車的設計,主要內容為舉升機構的設計與校核,和液壓控制系統的設計。論文選題具備一定的實用應用價值,難易程度適中,工作量飽滿。論文內容表明該生具備一定的綜合應用專業知識能力,研究思路比較清晰。論文文字順暢,包括一定的文獻檢索內容,三維模型繪制較好。論文所使用的概念準確
,計算過程較為合理,校核過程比較完備。論文的整體結構合理
,文字通順,公式、圖表較多,能夠體現工作內容和設計流程。該生已達到本科生培養目標要求,建議準予答辯。
評閱人簽字:張?jiān)坪?評閱人工作單位:機械工程學院日期:2018-05-21
答辯紀錄
學生姓名:XX 專業班級:XX
畢業論文(設計)題目: 隨車起重運輸車舉升機構設計
答辯時間:2018年05月23日 時 分 ~ 時 分
答辯委員會(答 辯小組)成員
主任委員(組長): XX XX(副組長)
委 員(組 員): XX XX
答辯委員會(答辯小組)提出的問題和答辯情況
問題1:舉升高度,重量? 回 答: 舉升高度為6.3m
重量為2300kg
問題2:液壓是用什么畫的? 回 答: 是使用AISOI畫的
問題3:怎么提升舉升機構穩定性? 回 答: 使用更高強度的材料。
問題4:技術要求是怎樣的?
回 答: 技術要求是保證機械臂能達到強度標準。問題5:液壓的造型是按標準造型的嗎?
回 答: 雖然有細節錯誤,但是按標準造型的。
記錄人: 2018年05月23日
答辯委員會評價表
評價內容
具體要求
總分
評分
自述總結
思路清晰,語言表達準確,概念清楚,論點正確,分析歸納合理
10
8
答辯過程
能夠正確回答所提出的問題,基本概念清楚,有理論根據
10
7
選題質量
符合培養目標要求,有一定的研究?jī)r(jià)值和實踐意義,有一定的
開拓性、創新性,深度、難度適宜,工作量飽滿
5
4
完成質量
文題相符,概念準確,分析、論證、計算、設計、實驗等正確
合理,結論明確;論文結構、撰寫格式、圖表等符合基本規
10
7
能力水平
有較強的綜合運用知識能力、科研方法運用能力、中文表
達與外語應用能力、文獻資料檢索能力、計算機應用能力
10
7
答辯委員會評分合計
33
答辯委員會評語
XX同學在畢業設計工作期間,工作努力,態度比較認真,能遵守各項紀律,表現一般。
能按時、全面、獨立地完成與畢業設計有關的各環節工作,具有一定的綜合分析問題和解決問題的能力。
論文立論正確,理論分析無原則性的錯誤,解決問題方案比較實用,結論正確。
論文使用的概念正確,語句通順,條理比較清楚。
論文中使用的圖表,設計中的圖紙?jiān)跁鴮懞椭谱鲿r(shí),能夠執行國家相關標準,基本規范。
能夠獨立查閱文獻,外語應用能力一般,原始數據搜集得當,實驗或計算結論準確可靠。
答辯過程中,能夠簡明地闡述論文的主要內容,回答問題基本正確,但缺乏深入地分析。
答辯成績: 33 答辯委員會主任: XX 2018年05月29日
成績?cè)u(píng)定
項目分類
成績?cè)u(píng)定
過程管理評分
13
指導教師評分
16
評閱人評分
15
答辯委員會評分
33
總分
77
成績等級
C
成績等級按“A、B、C、D、F”記載
成績審核人簽章: XX
學院審核人簽章: XX
收藏