購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。帶三維備注的都有三維源文件，由于部分三維子文件較多，店主做了壓縮打包，都可以保證打開的，三維預覽圖都是店主用電腦打開后截圖的，具體請見文件預覽，有不明白之處，可咨詢QQ:1304139763===========題目最后備注XX系列，只是店主整理分類，與內容無關，請忽視
鹽城工學院畢業設計說明書 2006
玩具汽車上蓋模具設計及型腔加工仿真
摘要：本課題設計是對玩具汽車的模具設計和成型零件的加工仿真。設計過程中采用Pro/E Wildfire 2.0進行三維造型、分型面設計和模流分析，使用EMX 4.1模塊進行模具整體設計，使用Master cam 9.0進行模具型腔仿真加工。
本模具依據廠方給定的注塑機型號和經濟性確定型腔為一模四腔；考慮模具中的成型位置及精度等諸多種因素的影響，選取分型面在塑件的底面；為使塑件能夠快速均勻冷卻，冷卻流道布置為環繞式；為使鑲塊結構不發生泄漏，使用負壓冷卻水系統；采用平衡式分流道、側澆口，使型腔同時得到均勻的充填和成型；頂出機構是制品的脫模裝置，依據塑件結構采用12根頂桿；由于塑件是薄壁結構可能出現注塑不完整，通過模流分析驗證注塑流體可以充滿型腔，符合設計要求。根據設計參數，使用EMX對模具整體設計。分析型腔的加工工藝，在Master cam 9.0中完成刀具路徑設定，確定數控加工代碼，通過仿真加工確定是否滿足加工要求。
通過使用模具設計應用軟件，使模具設計效率大大提高，完全符合設計要求。
關鍵詞：模具設計；加工仿真；注塑模具；CAM技術
The design of the toy automobile top shell mould And
the simulation processing of the mold cavity
Abstract: This topic is to design the toy automobile mold and the simulation processing of the mold cavity. In the design process, Pro/E Wildfire 2.0 were used to construct carries on the three dimensional modeling, design demould the plane and analyse mold flows, the EMX 4.1 modules were used to carry on the mold overall design, Master cam 9.0 were used to carry on the mold cavity simulation processing.
This mold according as the injection molding machine model and the efficient deterministic cavity which assigns based on the factory is four cavities ; Considered in the mold takes shape the position and the precision and so on the various many kinds of factors influence, a selection divided profile is modeling a bottom surface; In order to cause to model to be able the fast uniform cooling, cools the flow channel arrangement for to surround the type; In order to cause to inlay the block structure not to occur divulges, use negative pressure cooling water system; Uses a balance -like divided flow channel, the side runner, at the same time the causing cavity obtains even fills and takes shape; prop up the organization is the product taking off patterns installment, go on the basis models a structure to use 12 mandril ; Because models are the thin-wall construction possibly appears casts not completely, get across flows the analysis confirmation the mold to cast the fluid to be possible the filling cavity, conforms to the design requirement. According to the design variable, uses EMX for the mold overall design. The analysis cavity processing technics, completes the cutting tool way hypothesis in Master cam 9.0, the definite numerical control processing code, through the simulation processing determined whether satisfies the processing request.
Through the use mold design application software, makes the mold rated capacity to enhance greatly, conforms to the design requirement completely.
Key words: mold design; processing simulation; enjection mould; cam technology