0443-側裝式少齒差傳動卷?yè)P(yáng)機設計【含4張CAD圖】

0443-側裝式少齒差傳動卷?yè)P(yáng)機設計【含4張CAD圖】,含4張CAD圖,側裝式少齒差,傳動,卷?yè)P(yáng)機,設計,cad 中文摘要 側裝式少齒差傳動卷?yè)P(yáng)機設計 [摘要]漸開線少齒差傳動卷?yè)P(yáng)機是諸多傳動形式卷?yè)P(yáng)機中的一種。利用少齒差傳動機構的優越性可改進和提高建筑機械等設備的傳動結構技術性能，將漸開線少齒差行星齒輪傳動應用于建筑卷?yè)P(yáng)機的動力傳輸系統，可以減小機構尺寸，提高傳動質量，同時它的傳動比大、承載能力大、壽命長，也降低了制造成本。但是在漸開線少齒差內嚙合傳動中,由于內齒輪和外齒輪的齒數差少,在切削和裝配時常常會產生各種干涉,以致造成報廢。因此,為了保證內嚙合傳動的正常運轉,設計時要滿足幾個條件，主要的兩個限制條件是，即要保證不發生齒廓重迭干涉和嚙合率不小于1。少齒差內嚙合的設計非常煩瑣,尤其是齒廓重迭干涉驗算最為麻煩，這也是解決設計問題的核心所在。在設計過程中多次變換變位系數和齒頂高系數以滿足條件。 本文主要對少齒差行星齒輪傳動的設計計算進行了說明。其中包括工作原理、參數選擇、幾何計算等。并根據結構尺寸設計零件、選擇標準件，然后再進行強度或者壽命校核計算。 [關鍵詞] 卷?yè)P(yáng)機；漸開線少齒差傳動；齒廓重迭干涉；少齒差內嚙合 Design of the side installment hoist of small tooth number difference planetary transmission [Abstract] Involute gear transmission with small tooth number difference hoist is one kind of transmissions forms hoist. It can improve and enhance the transmission structure technical performance of the construction machinery using the of small tooth number difference planetary transmission. If the involute gear transmission with small tooth number difference transmission will apply for construction hoist transfer system, it can increased besides a reduction ingear size, and no interference will occur, and improves the transmission quality simultaneously its velocity ratio is big and the load capacity is big too, the life is long, and it also can reduce the production cost. But in the mesh inside of forma small tooth number difference transmission, because of the difference of annular gear and the external gear is few. It ofter causes interference in the cutting and the assembly, so that it may be waster. Therefore, in order to in guarantee meshes the transmission noramal work, the design must satisfy several conditions. The two main limiting condition is that it must guarantee does not have the tooth outline overlap interference and meshing rate smaller than 1.The design of the mesh inside of forma small tooth number difference is troublesome, extremely the checking computations of the tooth outline overlap difference. It is also the core of the solution in the design. It need to transform the dislodgement coefficient and the gear addendum coefficient many times to satisfy the condition in the design process. This paper describes the method which is used for designing the drive of the few difference in number of teeth. Including principle of work, parameter choice, geometry computation and so on. Choose the standard letter on the basis of the structure size design components, then carry on the computation of the intensity or the life examination. [Key words] hoist machine;involute gear transmission with small tooth number difference;tooth outline overlap interference ;small tooth number difference internal mesh. VI