購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。。【注】：dwg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
附錄Ⅰ
滅茬機常見故障九種
一、滅茬機在作業過程中，拖拉機冒黑煙并伴有打滑等現象，這是由于滅茬機負荷過載所致。負荷過重主要由于滅茬深度太大、土壤粘重或過硬而造成的。遇此情況應適當減少耕深或耕幅，或者將擋位調低，降低機組的前進速度。
二、滅茬機作業過程中出現跳動、抖動現象，是由于刀片沒有按照使用說明書進行安裝或因土壤堅硬等原因引起的。遇此情況因停機檢查刀片的安裝情況，若刀片裝錯，應予以糾正。若土壤堅硬應降低機組的前進速度，或增加機組的作業次數；第一遍先淺耕，第二遍再將滅茬機調到預定深度，以滿足耕深要求。
三、滅茬機作業質量出現問題。間斷拋出大塊土坷垃或成條出現大土塊。間斷拋出大土塊是由于滅茬機刀片彎曲變形、折斷、丟失或嚴重磨損所致，應視具體情況予以矯正、焊接或更換新刀片；成條出現大土塊是由于機手操作不當引起，因為相鄰作業銜接不好，出現輕微漏耕現象，遇此情況，應告誡駕駛員，作業時銜接行應有5～10厘米的銜接區。
四、滅茬后地面出現凹凸不平現象。這是由于機組前進速度與滅茬刀軸的轉速搭配不當引起，應降低擋位作業，若質量仍無改觀，應停機檢查，找出原因，予以解決。
五、齒輪箱內有雜音?？梢詮囊韵聨讉€方面進行檢查：齒輪箱內有無異物，傘形齒輪間隙調整是否得當，軸承有無損壞，齒輪有無“掉牙”現象。應根據檢查的具體情況予以排除、修理。
六、作業過程中，滅茬機刀軸突然出現轉不動或轉動明顯不如前靈活，很可能是由于齒輪箱內齒輪損壞而咬死、軸承碎裂咬死、刀軸側板變形、刀軸彎曲變形、刀軸纏草堵泥嚴重或因齒輪、軸承損壞引起傘齒輪無齒側間隙等原因引起。應仔細檢查各部分，并根據實際情況，排除故障。
七、滅茬作業中有金屬碰撞聲和敲擊聲，可能由如下原因引起的：傳動齒輪過松與傳動箱體相碰；刀軸兩端刀片、左支臂或傳動箱體變形后相互碰撞；刀片固定螺絲松動等。找出原因，調整鏈條，矯正或更換零部件，擰緊固定螺栓。
八、齒輪箱漏油是由于油封、紙墊損壞或箱體有裂紋造成的。排除方法是更換損壞或老化的油封、紙墊，修復或更換箱體等。
九、拖板鏈條折斷是由于運輸過程中未升到預定高度，鏈條拉得不緊所致。修復鏈條，在運輸過程中將其固定到最高位置并拉緊鏈條。
在我國，目前的驅動型耕作機械產品有滅茬機及復式作業機、驅動式圓盤犁、耕耙犁、水田驅動耙、立式轉齒耙等，但產量比較大的主要是旋耕機。當前，批量生產和推廣使用的2．2～76．4kW手扶拖拉機和乘坐式拖拉機配套旋耕機三大系列145種產品。90年代以來，國內又研制了一批旋耕復式作業機具新產品，逐步投放市場?，F(xiàn)在，國內大中拖配套旋耕機保有量約15萬臺，手拖和小四輪配套旋耕機約200萬臺。旋耕機在南方水稻生產機械化應用中已占80％比例，北方的水稻生產、蔬菜種植和旱地滅茬整地也廣泛采用了旋耕機械。
南稻北移，種植面積迅速增加，擴大了對旋耕機械的市場需求。水稻是高產作物，種植水稻有較高的經濟效益。近年來，在我國北方實施種植結構調整，相應的農機裝備結構正在發生變化，迫切需要從技術上、經濟上合理配備適應水旱田作業的拖拉機及配套農機具。黑龍江墾區原以旱田種植麥豆為主，并以傳統的旱地鏵式犁與其配套的圓盤耙、平地機、耢地機等作為耕整地機具。1993年，擁有旋耕機僅1631臺，而當年水稻種植面積為1500萬畝，顯然不知識水稻生產的發展。近10年來，黑龍江墾區大量購進手扶拖拉機和上海50等中型輪式拖拉機及配套的旋耕。
農業產業化、集約化、規?；?jīng)營需要大型高效旋耕機械。隨著我國農業產業化和適度規模經營的發展，對大中型農業機械的市場需求也日漸增大。不僅是農墾系統國營之農場，而且鄉村農機服務站又及個體的農機專業戶，也需要更新和添置大中型農業機械。對黑龍江墾區的調查表明，近年大量購置的水田耕整地機械已由中小功率拖拉機旋耕機組變化為鐵牛654和LF80―904WD等大中功率輪式拖拉機及配套旋耕機。農機專業戶使用這些大中型機械從事機耕服務，一般1～2年可回收本金，有誘人的經濟效益。
附錄Ⅱ（英文翻譯）
The rotary cultivator common fault of nine
Rotary tiller during operation, tractor black smoke with slip phenomenon, which is due to the rotary tiller overloading. Overloading mainly due to the rotary tiller depth is too large, heavy clay soil or excellent. If this happens should be appropriate to reduce the tillage depth or Working width or lower the gear to reduce the forward speed of the unit. During the operation of the rotary tiller appear jerky, jitter phenomenon is caused because the blade did not follow the manual installation or hard soil. In this case the result of the installation of stop and check the blade, blade installed wrong, and should be corrected. If the soil is hard and should reduce the forward speed of the unit, or to increase the number of unit operations; shallow plowing first pass, second pass and then rotary tiller transferred to a predetermined depth, tillage depth to meet the requirements. , Rotary tiller job quality problems. Intermittent throw the bulk soil Ke La, or large clods. Intermittent throw clods rotary tiller blade bending deformation, broken, lost or badly worn, as the case may be corrected, welding or replacement blade; into big clods is caused due to improper operation of the machine in hand , convergence area adjacent on connection with bad the slight leakage farming phenomenon, In this case, the driver should be warned, the convergence operating line should be 5 to 10 cm. , Rotary ground after the uneven phenomenon. This is due to the the unit forward speed and Rotary Blade shaft speed mismatches caused lower gear operation, should stop to check to find out the causes to be addressed if the quality is still no change. Fifth, the gear box noise. Can be checked from the following aspects: gear box without foreign body, bevel gears gap to adjust it properly, bearing for damage and whether the gear out teeth "phenomenon. Be excluded should be based on the specific circumstances of the inspection, repair. 6, during the operation, rotary tiller blade shaft suddenly would not turn in or turn was not as good as pre-flexible, is likely to be killed due to damage to the gear box gear, bearing fragmentation killed, knife shaft side plate deformation, the knife shaft bending deformation, knife shaft is wrapped around the grass blocking mud serious or bearing damage caused due to gear, bevel gear backlash causes. Each part should be carefully examined, according to the actual situation, troubleshooting. Rotary operating sound of metal crash and percussion, which may be caused by the following reasons: the drive chain is too loose and the transmission box collide; deformation of the shaft at both ends of the knife blade, left arm or transmission box. collision; blade screws loose. Find out why, adjust the chain, correction or replacement parts, unscrew the bolts firmly. The eight gearbox oil spill oil seal, paper pad is damaged or the box cracks caused. Remedy is to replace damaged or aging oil seals, paper pads, repair, or replacement of the box. IX carriage broken chain is not scheduled to rise to the height of the transport process, pull the chain Undertightening the due. Repair chain during transport is fixed to the highest position and tensioning the chain.
In China, the current-driven farming machinery products rotary tiller and duplex operation, the driven disc plow, Reciprocating harrow, paddy harrows, vertical turn tooth harrow, but the yield is the relatively large rotary tiller . Currently, mass production and promote the use of 2.2 to 76.4kW walking tractor and ride-on tractor rotary tiller three series of 145 kinds of products. Since the 1990s, the country has developed a number of rotary tiller duplex operation tools with new products, and gradually put on the market. Now, the domestic large and medium-sized drag supporting rotary tiller to maintain about 15 million units, the Trolley and small four-wheel supporting rotary tiller about 200 million units. Rotary tiller in the Southern rice production mechanization applications accounted for 80% of the northern rice production, vegetable cultivation and dry stubble soil preparation with a wide range of Rotary Machinery. Southern rice the north, the area under cultivation increased rapidly expanding market demand for rotary tillage machinery. Rice is a high-yielding crops, planting rice has a higher economic efficiency. In recent years, the implementation of the planting structure adjustment in the north of China, the farm machinery and equipment structure is changing, there is an urgent need to technically and economically reasonable job with the adaptation to water upland tractors and related farm machinery. Heilongjiang reclamation area was originally planted to upland wheat bean-based, and the the traditional dryland plow its support of the disc harrow, graders, Lao and machine as tillage to machinery. In 1993, with only 1631 units rotary tiller, and the rice cultivation area of 1,500 hectares, is clearly not the knowledge of rice production development. The past 10 years, Heilongjiang reclamation area to buy lots of walking tractor and 50 medium-sized wheeled tractors and related Rotary. The industrialization of agriculture, intensive, large-scale operation requires large and efficient rotary tillage machinery. With the development of China's agricultural industrialization and the appropriate scale of operation, an increasing market demand for large and medium-sized agricultural machinery. Not only is the state-owned farms state-owned farms, agricultural and rural agricultural service stations and individual specialized households, updates and additions to large and medium-sized agricultural machinery. Of Heilongjiang Reclamation Area survey showed that changes in the purchase of paddy fields in recent years, a large number of tillage to machinery by small and medium-power tractor rotary tiller unit power wheeled tractor 654 and LF80-904WD large and medium-sized tractors and related rotary tiller. Agricultural machinery specialized households engaged in these large and medium-sized mechanical plowing services, generally 1 to 2 years recyclable principal attractive economic benefits.
5