購買設計請充值后下載，，資源目錄下的文件所見即所得，都可以點開預覽，，資料完整，充值下載可得到資源目錄里的所有文件。。?！咀ⅰ浚篸wg后綴為CAD圖紙，doc,docx為WORD文檔，原稿無水印，可編輯。。。具體請見文件預覽，有不明白之處，可咨詢QQ:12401814
車運原煤自動采樣系統設計
（控制系統設計）
摘要
論文闡述了可編程控制器PLC在車運原煤自動采樣系統中的應用。主要介紹了車運原煤自動采樣的PLC控制系統總體方案設計，設計出了硬件控制電路、軟件程序梯形圖
及指令表，并給出了系統組成框圖和程序流程圖。
我設計的是對汽車所運原煤進行采樣的自動小車控制系統，實現小車的橫向、大車的縱向移動以及采樣螺旋探頭的上升、下降過程。系統采用可編程控制器控制。
采樣工作過程如下：
當載運車輛到達采樣點時，人工啟動采樣系統，采樣小車先橫向運行指定時間后停止，然后大車進行縱向運行，到指定位置時停止，螺旋采樣筒旋轉，采樣頭下降并旋轉進入汽車煤層，到達一定深度后稍做停留，將車載原煤載入采樣筒上方的采樣斗中；然后采樣頭上升，大車小車后退回原位，采樣頭料門打開，煤樣流入料斗，取樣完成。
入廠原煤采制樣裝置是洗煤廠入廠原煤質量分析中的重要設備。利用可編程序控制器，實現對入廠原煤采制樣裝置的自動控制，不僅簡化了操作，而且提高了系統的可靠性。
關鍵詞∶ 可編程控制器；采樣系統；自動控制
Abstract
The thesis elaborated the programmable controller PLC in car carry automatic sampling system of raw coal of application. The thesis mainly introduced the total project design of PLC control system that the car luck raw coal automatically sample, design the hardware control electric circuit, software procedure trapezoid chart
And the instruction gage, and give the system composition block diagram and the procedure flow chart.
What I design is an automatic and small car control system that samples to the autocar raw coal progress carry, carry out the small car of transversal and big car travel and sample the rising that screw stretch forward and descend the process lengthways. The system adopts the programmable controller control.
Sampled the process of operate as follows:
When transport the vehicle to arrive the sampling spot, the artificial start sampling system, sample the small car to traverse the running first to stop after specify time, then the big car progress circulates lengthways, while arriving to specify the place stop, the screw sampling tube revolution, sample the prinipal to descend and revolve into the coal seam, coalbed of autocar , make to stop over slightly after arriving the certain depth, carry car the sampling bucket that the raw coal loads in to sample on the above of the tube. Then sample the rising of prinipal, the small car of big car recoil to return to home position, sampling the prinipal to anticipate the door to open, the coal sample flows in to anticipate the bucket, the sampling complete.
Go into the raw coal of plant adopts to make the kind apparatus is important equipments that washes the coal plant to go into the plant raw coal mass analysis. Make use of the programmable preface controller, carry out to adopt the automatic control of make the kind apparatus towards going into the raw coal of plant, not only simplified the operation, but also raised the system reliability.
Key words: Programmable Logic Controller ；Sample system ；Automatic control
目 錄
摘要………………………………………………………………………………… ⅰ
Abstract…………………………………………………………………………… ⅱ
目錄………………………………………………………………………………… ⅲ
緒論………………………………………………………………………………… 1
第一章 車運原煤自動采樣系統總體方案設計 ………………………………… 2
一、總體方案確定…………………………………………………………… 2
二、設計采制樣裝置及其主要設備………………………………………… 7
第二章 車運原煤自動采樣控制系統設計 ……………………………………… 11
一、采制樣裝置的PLC控制系統組成 …………………………………… 11
二、PLC 的工作原理和結構組成…………………………………………… 11
三、PLC 的選擇……………………………………………………………… 15
四、CPU 模塊型式及電源模塊型式規格選擇……………………………… 20
五、變頻器的選型…………………………………………………………… 22
第三章 車運原煤自動采樣軟件系統的設計 …………………………………… 28
一、建立I/O地址分配表…………………………………………………… 28
二、端子接線圖……………………………………………………………… 29
三、程序流程圖……………………………………………………………… 29
四、PLC 程序設計 ………………………………………………………… 31
五、PLC 控制系統抗干擾能力……………………………………………… 38
結論………………………………………………………………………………… 41
致謝………………………………………………………………………………… 42
參考文獻…………………………………………………………………………… 43
附錄………………………………………………………………………………… 44
一、英文資料及中文翻譯………………………………………………………… 44
二、梯形圖………………………………………………………………………… 59
iii