1646-圓盤剪切機設計

1646-圓盤剪切機設計,圓盤,剪切,設計 鞍山科技大學本科生畢業設計（論文） 第 I 頁圓盤剪切機設計摘 要現在各國工業迅猛發展，鋼鐵企業是國民經濟的主要支柱，它的發展狀況很大程度上可以反映出國家的實力?，F(xiàn)代鋼鐵冶金業發展的一個著眼點就是在對鋼材的處理速度。圓盤剪切機就是其中的一臺重要設備。圓盤剪切機通常設置在精整作業線上，用來將運動著的鋼板的縱向邊緣切齊或切成窄帶鋼。根據其用途可分為兩種類型：剪切板邊的圓盤剪和剪切帶鋼的圓盤剪。本文中對圓盤剪切機的設計計算是在對鞍山鋼鐵集團公司冷軋廠 1700 橫切機組大量調研的背景下進行的。通過對圓盤剪切機及相關設備結構進行了深入了解，并從材料力學、動力學和經濟學的角度出發，對圓盤剪切機的主傳動系統，壓下系統、側間隙調整機構進行了設計。重點包括電動機的計算選取、軸和齒輪的設計，以及其他傳動裝置和執行機構的設計等，同時對部分主要零部件進行了強度校核。本次設計的改進點：首先，在徑向間隙調整機構連桿機構，其二，側向間隙調整增加自鎖裝置。其三，寬度調整采用行星齒輪減速機。最后增加了測速機構。本圓盤剪切機可普遍用于橫切機組、酸洗機組等。關鍵詞：圓盤剪切機，帶鋼，壓下裝置，強度校核鞍山科技大學本科生畢業設計（論文） 第 II 頁The disc alligator shears design AbstractThe industry of various countries develops rapidly now, the steel, as the main pillar of industry, its development can reflect the national strength to a great extent. Modern steel metallurgy industry one starting point that develop in to processing speeds. Disc shears is an important equipment among them.Disc shear machine set up in finishing production line. It usually uses to cutting neat the movement steel plate longitudinal edge and cut the strip into narrow one. It can be divided into two kinds according to its use: disc shears of cut stencil plate’s side and disc shears of cut strip.The disc shears design calculation is taken in makes the massive investigation to the ANSHAN steel group Cold-rolling mill 1700 transverse cutting aircrew as the background. We have thorough understanding to the disc shears and the correlation equipment. We had very designed to the main transmission system, depress the system and gap adjustment organization, we are carry on these designs from the materials mechanics angle, dynamics and economic. The main content including electrical machinery selection, Axis and gear design, Implementing agency design and so on, and the same time, we make the optimized improvement and the intensity examination to the major parts. This design improvement spot: First, in radial clearance adjusting mechanism link motion gear, second, backlash adjustment increase self-locking installment. Third, the width control uses the planet gear speed reducer. Finally increased has measured the fast organization. This disc shears may use in the transverse cutting unit, the acid pickling unit generally and so on.Key words: Disc shear, strip, depress the system, the intensity examination鞍山科技大學本科生畢業設計（論文） 第 III 頁目 錄1.緒論 .......................................................................................................................................11.1 選題的背景和目的 ...........................................................................................................11.2 圓盤式剪切機國內外的發展現狀 ..................................................................................11.3 圓盤剪切機研究的內容和方法 ......................................................................................31.3.1 圓盤剪切機在機組的布置和作用.............................................................................31.3.2 圓盤剪切機的類型和特點........................................................................................51.3.3 圓盤剪切機設計內容和方法....................................................................................52. 設計方案的選擇和方案評述................................................................................................63. 電機容量的計算....................................................................................................................83.1 定性選電機 ......................................................................................................................83.2 選擇電動機的容量 ..........................................................................................................83.3 確定轉速 ........................................................................................................................113.4 電動機的校核 ................................................................................................................124. 主要零件強度計算校核......................................................................................................144.1 齒輪的計算與校核 ........................................................................................................144.1.1 齒輪的計算...............................................................................................................144.1.2 按接觸疲勞強度校核..............................................................................................144.1.3 按彎曲疲勞強度校核..............................................................................................184.2 傳動軸的強度校核計算 ................................................................................................204.2.1 軸的材料及其機械性能...........................................................................................204.2.2 軸的模型及傳遞功率的確定..................................................................................204.2.3 按彎扭合成進行軸的強度校核..............................................................................214.2.4 按疲勞強度進行精確校核......................................................................................244.3 軸承的選取及校核 ........................................................................................................284.3.1 根據工作條件選取軸承類型..................................................................................284.3.2 根據軸承結構確定軸承的型號...............................................................................284.3.3 軸承的壽命校核.......................................................................................................28鞍山科技大學本科生畢業設計（論文） 第 IV 頁4.3.4 驗算軸承的極限轉速..............................................................................................314.4.2 鍵的尺寸的選擇......................................................................................................314.4.3 鍵的強度校核...........................................................................................................315. 聯軸器的選擇......................................................................................................................335.1 聯軸器的分類 .................................................................................................................335.2 聯軸器的選擇 .................................................................................................................335.3 聯軸器的強度計算.....................................................................................................336. 系統的潤滑..........................................................................................................................356.1 潤滑劑的種類 .................................................................................................................356.2 潤滑方式的選擇 .............................................................................................................356.3 潤滑方式的選擇確定 .....................................................................................................356.3.1 齒輪減速器的潤滑方式..........................................................................................356.3.2 部分傳動齒輪、軸承的潤滑方式..........................................................................367. 試車方法和對控制系統的要求..........................................................................................377.1 試車要求 ........................................................................................................................377.2 對控制系統的要求 ........................................................................................................378. 設備可靠性與經濟評價......................................................................................................388.1 機械設備的有效度 ........................................................................................................388.2 機械設備的投資回收期 ................................................................................................38總結...........................................................................................................................................40致謝...........................................................................................................................................41參考文獻...................................................................................................................................42