2282 1616點陣LED電子顯示屏
2282 1616點陣LED電子顯示屏,點陣,led,電子顯示屏
16×16 點陣顯示屏成功點亮??！2009-04-17 09:59看到江同學的 3216屏（www.jiangx.net），對于我來說，稍顯復雜，所以決定做個 1616的屏看看效果，原理圖就是以下了，注意做 1616時，要去掉一個 74LS154(當然這里也能換用 74HC154，雖然功耗大，但價格較低)，經過兩天的奮斗，終于完工了。簡單的調試后，點亮了?。【巶€(gè)流動顯示的程序，哈哈，很炫啊。心動不如趕快行動?。?！我是把點陣塊焊到一塊板子上，可方便檢查有無虛焊，控制部分放到了另一張板上，做成的實物圖就是下面的了，視頻在這里：http://u.youku.com/springvirus （注：以下原理圖均來自 www.jiangx.net）/*********************************************************程序名稱：LED1616 點陣流動顯示漢字簡要說明：最大可顯示 16*16漢字P0口接上行線，P2 口接下行線，P3 口接掃描線編 寫： JiangX.net改 編： springvirus*********************************************************/#include #define hang1 P0 //上行線#define hang2 P2 //下行線#define lie P1 //列線#define sum sizeof(hanzi)/32 //自動計算漢字字?jǐn)?shù)/*****參數設置*****/#define ziti 16 //字體大小（寬度）#define light 50 //顯示亮度#define move_speed 50 //移動速度unsigned char code hanzi[]={/*-- 文字: 自 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x00,0x00,0xF8,0x48,0x48,0x4C,0x4B,0x4A,0x48,0x48,0x48,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x44,0x44,0x44,0x44,0x44,0x44,0x44,0x44,0xFF,0x00,0x00,0x00,/*-- 文字: 制 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x50,0x4F,0x4A,0x48,0xFF,0x48,0x48,0x48,0x00,0xFC,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x3F,0x01,0x01,0xFF,0x21,0x61,0x3F,0x00,0x0F,0x40,0x80,0x7F,0x00,0x00,/*-- 文字: 小 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x00,0x00,0xC0,0x70,0x20,0x00,0xFF,0x00,0x10,0x20,0xC0,0x80,0x00,0x00,0x00,0x04,0x02,0x01,0x00,0x00,0x40,0x80,0x7F,0x00,0x00,0x00,0x00,0x01,0x07,0x02,0x00,/*-- 文字: 型 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x10,0x12,0x92,0x7E,0x12,0x12,0xFE,0x12,0x12,0x10,0xFC,0x00,0x00,0xFF,0x00,0x00,0x40,0x42,0x49,0x48,0x48,0x48,0x49,0x7E,0x48,0x48,0x48,0x4A,0x4C,0x4B,0x40,0x00,/*-- 文字: 點 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x00,0x00,0xE0,0x20,0x20,0x20,0x3F,0x24,0x24,0x24,0xF4,0x24,0x00,0x00,0x00,0x00,0x40,0x30,0x07,0x12,0x62,0x02,0x0A,0x12,0x62,0x02,0x0F,0x10,0x60,0x00,0x00,/*-- 文字: 陣 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0xFE,0x02,0x12,0x2A,0xC6,0x88,0xC8,0xB8,0x8F,0xE8,0x88,0x88,0x88,0x88,0x00,0x00,0xFF,0x00,0x02,0x04,0x03,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x04,0x00,/*-- 文字: 顯 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x00,0x00,0x3E,0x2A,0xEA,0x2A,0x2A,0x2A,0xEA,0x2A,0x3E,0x00,0x00,0x00,0x00,0x20,0x21,0x22,0x2C,0x20,0x3F,0x20,0x20,0x20,0x3F,0x28,0x24,0x23,0x20,0x20,0x00,/*-- 文字: 示 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x20,0x20,0x22,0x22,0x22,0x22,0xE2,0x22,0x22,0x22,0x22,0x22,0x20,0x20,0x00,0x10,0x08,0x04,0x03,0x00,0x40,0x80,0x7F,0x00,0x00,0x01,0x02,0x0C,0x18,0x00,0x00,/*-- 文字: 系 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x00,0x00,0x02,0x22,0xB2,0xAA,0x66,0x62,0x22,0x11,0x4D,0x81,0x01,0x01,0x00,0x00,0x00,0x40,0x21,0x13,0x09,0x05,0x41,0x81,0x7F,0x01,0x05,0x09,0x13,0x62,0x00,0x00,/*-- 文字: 統 --*//*-- 宋體 12; 此字體下對應的點陣為：寬 x高=16x16 --*/0x20,0x30,0x2C,0xA3,0x60,0x10,0x84,0xC4,0xA4,0x9D,0x86,0x84,0xA4,0xC4,0x84,0x00,0x20,0x22,0x23,0x12,0x12,0x92,0x40,0x30,0x0F,0x00,0x00,0x3F,0x40,0x41,0x70,0x00,/*****空白,用于區分顯示內容的頭和尾*****/0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};uint k=0,j; //移位變量,k:移位個數uint a=0; //用于軟件延時 ulong s=(sum+1)*ziti; //s為全部列數uchar disbuf[16][2]; //定義顯示緩沖區（16 行兩列的二維數組以開辟 1個 16*16漢字的空間）bit move_st; //移動標志/*****可變延時*****/void delay(void) {uchar i;for(i=0;i=move_speed) //move_speed控制移動速度{ if(k>s-ziti-1)k=0; //整屏移動列數 k1=k/ziti;k2=k%ziti;j=ziti*2*k1+k2; //顯示指針 k++;move_st=1;a=0;} }/*****裝載顯示數據至緩沖區*****/void load_hanzi(void){ uchar i;run_move();if(move_st){ for(i=0;i<15;i++){disbuf[i][0]=disbuf[i+1][0];//移位處理disbuf[i][1]=disbuf[i+1][1];//移位處理} disbuf[15][0]=hanzi[j];disbuf[15][1]=(hanzi[ziti+j]); move_st=0; } }/*****掃描顯示數據緩沖區的內容*****/void display(void){ uchar i;for (i=0;i<16;i++){lie=i; hang1=disbuf[i][0];hang2=disbuf[i][1];delay();hang1=0;hang2=0; }}/*****主程序*****/void main (void){ init();EA=1; //開中斷TR0=1; ET0=1; while(1){ load_hanzi();display(); }}
收藏