3791 圓蓋注塑模設計

3791 圓蓋注塑模設計,注塑,設計 畢業設計目錄緒　論 ...............................................................1第 1 章 注射模具的設計 ................................................21.1　塑件分析與模具材料和注射機的選取 .............................21.1.1 塑件結構分析 .............................................21.1.2 塑件零件圖技術要求分析 ...................................21.2 塑料材料的成型特性與工藝參數 ..................................21.2.1 基本特性： ...............................................21.2.2 主要用途 .................................................21.3 模具材料的選取及熱處理 ........................................31.4 注射機的選取 ..................................................3第 2 章　確定模具的結構方案 ...........................................52.1 確定塑件在模具中的位置和分型面位置 ............................52.1.1 型腔數目的確定 ...........................................52.1.2 塑件在模具中的位置和分型面的方案確定 .....................62.2 選擇澆注系統與排氣系統的方式 ..................................62.2.1 澆注系統的設計和澆口的選擇 ...............................62.2.2　排氣系統的設計 ........................................102.3 成型零件的結構設計 ...........................................102.3.1 凹模 ....................................................112.3.2 凸模和型芯 ..............................................112.4　合模導向機構設計 ............................................122.4.1 導向機構的作用 ..........................................122.4.2 導柱導向機構 ............................................122.5 推出機構設計 .................................................142.5.1 推桿推出機構 ............................................152.5.2 推件板推出機構 ..........................................152.5.3 推出機構的導向與復位機構設計 ............................16畢業設計目錄2.6 側向分型與抽芯機構設計 .......................................172.6.1 手動側向分型抽芯機構 ....................................172.6.2 氣動或液壓側向分型與抽芯機構 ............................172.6.3 機動側向分型抽芯機構 ....................................182.7 溫度調節系統 .................................................192.7.1 模具溫度調節的重要性 ....................................20第 3 章　工作尺寸的計算和注射機的校核 ................................223.1 模架各零件的計算和選取 .......................................223.1.1 腔板尺寸的計算 ..........................................223.1.2 型芯固定板尺寸的計算 ....................................233.1.3 模架各板尺寸的選取與校核 ................................243.2 注射機的校核 .................................................243.2.1 校核鎖模力： ............................................253.2.2 校核注射壓力 ............................................253.2.3 校核模具的閉合厚度 ......................................253.2.4 校核最大開模行程 ........................................263.3 型腔、型心尺寸的計算 ........................................263.3.1 型腔尺寸的計算 ..........................................263.3.2 型芯尺寸的計算 ..........................................273.4 斜導柱和其它零件的尺寸計算 ...................................283.4.1 斜導柱的計算與確定 ......................................283.4.2 其它零件的計算 ..........................................30小　結 ..............................................................32致　謝 ..............................................................33參考文獻 ............................................................34